Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2013.11–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  U0265  Lost Communication with Parking Assist Monitor Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0265 Lost Communication with Parking Assist Monitor Module There is no communication from the television camera assembly.
·

Power source or inside television camera assembly

·

Television camera assembly CAN branch wire or connector

·

Television camera assembly

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


Main body ECU(multiplex network body ECU)

*1: w/ Navigation System

*2: w/ Audio and Visual System (for Radio and Display Type)

For vehicles with a parking assist monitor system (for camera built-in ECU).


WIRING DIAGRAM

C297921E02
0.156,0.135 4.646,0.5 4.49,0.365 12 false w/ Audio and Visual System (for Radio and Display Type): 1.698,0.813 2.833,1.219 1.135,0.406 10 false 7 1.698,1.385 2.833,1.792 1.135,0.406 10 false 18 0.438,1.875 1.573,2.281 1.135,0.406 10 false N32 0.448,2.052 2.635,2.479 2.188,0.427 10 false No. 5 CAN Junction Connector 5.656,0.906 6.792,1.313 1.135,0.406 10 false CANH 5.667,1.469 6.802,1.875 1.135,0.406 10 false CANL 5.417,0.813 6.552,1.219 1.135,0.406 10 false 4 5.417,1.385 6.552,1.792 1.135,0.406 10 false 1 5.438,2.823 6.573,3.229 1.135,0.406 10 false 6 5.438,3.396 6.573,3.802 1.135,0.406 10 false 5 5.667,3.5 6.802,3.906 1.135,0.406 10 false CGND 5.656,2.969 6.792,3.375 1.135,0.406 10 false CB+ 1.167,3.5 2.302,3.906 1.135,0.406 10 false CGND 1.688,3.396 2.823,3.802 1.135,0.406 10 false 23 1.271,2.99 2.406,3.396 1.135,0.406 10 false CA+ 1.688,2.865 2.823,3.271 1.135,0.406 10 false 11 0.448,3.854 1.583,4.26 1.135,0.406 10 false G159 0.448,4.01 2.125,4.385 1.677,0.375 10 false Radio and Display Receiver Assembly 2.313,3.698 5.24,3.969 2.927,0.271 10 false Shielded 5.448,3.854 6.583,4.26 1.135,0.406 10 false U22 5.469,4.021 6.625,4.417 1.156,0.396 10 false Television Camera Assembly 3.365,3.698 6.292,3.969 2.927,0.271 10 false Shielded 4.417,3.719 6.854,4.021 2.438,0.302 10 false Shielded

C297921E03
0.156,0.125 3.365,0.323 3.208,0.198 12 false w/ Navigation System: 1.698,0.813 2.833,1.219 1.135,0.406 10 false 7 1.698,1.385 2.833,1.792 1.135,0.406 10 false 18 0.438,1.875 1.573,2.281 1.135,0.406 10 false N32 0.448,2.052 2.635,2.479 2.188,0.427 10 false No. 5 CAN Junction Connector 5.656,0.906 6.792,1.313 1.135,0.406 10 false CANH 5.667,1.469 6.802,1.875 1.135,0.406 10 false CANL 5.417,0.813 6.552,1.219 1.135,0.406 10 false 4 5.417,1.385 6.552,1.792 1.135,0.406 10 false 1 5.438,2.823 6.573,3.229 1.135,0.406 10 false 6 5.438,3.396 6.573,3.802 1.135,0.406 10 false 5 5.667,3.5 6.802,3.906 1.135,0.406 10 false CGND 5.656,2.969 6.792,3.375 1.135,0.406 10 false CB+ 1.167,3.5 2.302,3.906 1.135,0.406 10 false CGND 1.688,3.396 2.823,3.802 1.135,0.406 10 false 23 1.271,2.99 2.406,3.396 1.135,0.406 10 false CA+ 1.688,2.865 2.823,3.271 1.135,0.406 10 false 11 0.573,3.854 1.708,4.26 1.135,0.406 10 false G158 0.583,4.031 1.781,4.427 1.198,0.396 10 false Navigation Receiver Assembly 2.292,3.729 3.427,4.135 1.135,0.406 10 false Shielded 5.448,3.854 6.583,4.26 1.135,0.406 10 false U22 5.469,4.01 6.656,4.448 1.188,0.438 10 false Television Camera Assembly 3.365,3.729 4.5,4.135 1.135,0.406 10 false Shielded 4.375,3.729 5.51,4.135 1.135,0.406 10 false Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
HINT:

If DTC U1002 is output from gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) A
DTC U1002 is output from main body ECU (multiplex network body ECU) B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE)

B

GO TO GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE)
a.
C297923C01
1.448,0.177 1.927,0.469 0.479,0.292 1.417,1.146 0.969,0.667 0.969,0.667 0.74,0.667 true 1.385,1.458 0.99,1.885 0.99,1.885 0.76,1.885 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.552,0.219 1.917,0.448 0.365,0.229 10 false U22 0.323,0.552 0.927,0.896 0.604,0.344 10 false CANL 0.344,1.771 0.948,2.115 0.604,0.344 10 false CANH
*a Front view of wire harness connector
(to Television Camera Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U22-4 (CANH) - U22-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK (w/ Audio and Visual System [for Radio and Display Type])
OK (w/ Navigation System)
NG



OK (w/ Audio and Visual System [for Radio and Display Type])

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

OK (w/ Navigation System)

5.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
C297923C02
1.448,0.177 1.927,0.469 0.479,0.292 2.604,1.875 2.354,1.875 2.354,1.875 1.958,1.448 true 1.646,1.469 1.25,1.896 1.25,1.896 1.021,1.896 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.552,0.219 1.917,0.448 0.365,0.229 10 false U22 2.667,1.781 3.271,2.125 0.604,0.344 10 false CB+ 0.594,1.781 1.198,2.125 0.604,0.344 10 false CGND
*a Front view of wire harness connector
(to Television Camera Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
U22-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U22-5 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G159 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U22-6 (CB+) - G159-11 (CA+) Always Below 1 Ω
U22-5 (CGND) - G159-23 (CGND) Always Below 1 Ω
U22-6 (CB+) or G159-11 (CA+) - Body ground Always 10 kΩ or higher
U22-5 (CGND) or G159-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
C297923C02
1.448,0.177 1.927,0.469 0.479,0.292 2.604,1.875 2.354,1.875 2.354,1.875 1.958,1.448 true 1.646,1.469 1.25,1.896 1.25,1.896 1.021,1.896 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.552,0.219 1.917,0.448 0.365,0.229 10 false U22 2.667,1.781 3.271,2.125 0.604,0.344 10 false CB+ 0.594,1.781 1.198,2.125 0.604,0.344 10 false CGND
*a Front view of wire harness connector
(to Television Camera Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
U22-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U22-5 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the G158 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U22-6 (CB+) - G158-11 (CA+) Always Below 1 Ω
U22-5 (CGND) - G158-23 (CGND) Always Below 1 Ω
U22-6 (CB+) or G158-11 (CA+) - Body ground Always 10 kΩ or higher
U22-5 (CGND) or G158-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR