Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for SD) › 2013.11–2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0104513 NAVIGATION SYSTEM(for SD) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for SD)  B157D  DAB Tuner Antenna Disconnected  


DESCRIPTION

This DTC is stored when a malfunction occurs in the DAB tuner antenna which is connected to the navigation receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157D DAB Tuner Antenna Disconnected The DAB tuner antenna is not connected
·

Roof antenna pole sub-assembly

·

Antenna with holder assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Navigation receiver assembly



CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


WIRING DIAGRAM

E289433E01
0.063,0.313 1.281,0.646 1.219,0.333 10 false Roof Antenna Pole Sub-assembly 0.229,1.896 1.51,2.229 1.281,0.333 10 false Antenna with Holder Assembly 2.042,2.177 3.281,2.51 1.24,0.333 10 false No. 3 Antenna Cord Sub-assembly 3.521,2.156 4.76,2.49 1.24,0.333 10 false No. 2 Antenna Cord Sub-assembly 5,2.146 5.969,2.49 0.969,0.344 10 false Antenna Cord Sub-assembly 5.896,2.833 7.125,3.198 1.229,0.365 10 false Navigation Receiver Assembly 2.698,0.979 2.875,1.167 0.177,0.188 10 false 1 3.146,0.979 3.292,1.177 0.146,0.198 10 false 2 3.833,0.979 3.979,1.177 0.146,0.198 10 false 2 4.271,0.99 4.448,1.177 0.177,0.188 10 false 1 4.938,0.99 5.115,1.177 0.177,0.188 10 false 1 5.458,0.979 5.635,1.167 0.177,0.188 10 false 1 5.385,1.292 5.677,1.479 0.292,0.188 10 false 1-a 4.938,1.292 5.229,1.479 0.292,0.188 10 false 1-a 4.167,1.292 4.458,1.479 0.292,0.188 10 false 1-a 3.802,1.292 4.094,1.479 0.292,0.188 10 false 2-a 3.052,1.313 3.344,1.5 0.292,0.188 10 false 2-a 2.698,1.292 2.99,1.479 0.292,0.188 10 false 1-a

PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.



Result:
Proceed to
OK
NG



OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK NAVIGATION RECEIVER ASSEMBLY
3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E288794C01
1.948,0.885 2.24,0.615 2.24,0.615 2.438,0.615 true 1.427,2.51 0.948,2.781 0.948,2.781 0.792,2.781 true 0.385,0.156 0.698,0.313 0.313,0.156 10 false *a 0.448,1.708 0.76,1.865 0.313,0.156 10 false *b 2.479,0.531 2.875,0.698 0.396,0.167 10 false 1-a 0.552,2.677 0.948,2.844 0.396,0.167 10 false 2-a
*a Front view of wire harness connector
(to Antenna with Holder Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna with holder assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
1-a - 2-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795C01
0.74,2.573 0.927,2.573 0.927,2.573 1.208,2.417 true 2.135,0.781 2.385,0.646 2.385,0.646 2.583,0.646 true 0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b 2.646,0.563 3.031,0.771 0.385,0.208 10 false 2-a 0.51,2.448 0.896,2.656 0.385,0.208 10 false 1-a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
2-a - 1-a Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
2-a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288803C01
2.042,0.823 2.354,0.667 2.354,0.667 2.531,0.667 true 1.771,2.698 2.323,2.354 2.323,2.354 2.5,2.354 true 0.229,0.094 0.542,0.25 0.313,0.156 10 false *a 0.292,1.854 0.604,2.01 0.313,0.156 10 false *b 2.594,0.604 3.01,0.771 0.417,0.167 10 false 1-a 2.531,2.302 2.948,2.469 0.417,0.167 10 false 1-a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the navigation receiver assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 1 Always Below 1 Ω
1-a - 1-a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1-a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

7.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

OK:

The roof antenna pole sub-assembly is installed properly.



Result:
Proceed to
OK
NG



OK

8.CHECK ANTENNA WITH HOLDER ASSEMBLY

NG

CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY

8.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for SD)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

NG