Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2013.11–2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABD  Short to +B in Buzzer  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

·

DTC C1ABD is stored when the blind spot monitor sensor RH detects a +B short in rear cross traffic alert buzzer (blind spot monitor buzzer) circuit.

·

DTC C1ABE is stored when the blind spot monitor sensor RH detects a ground short or open in rear cross traffic alert buzzer (blind spot monitor buzzer) circuit.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1ABD Short to +B in Buzzer Both of the following conditions are met:
·

Blind spot monitor main switch (warning cancel switch assembly) is on with ignition switch ON.

·

The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time.


·

Blind spot monitor sensor RH

·

Rear cross traffic alert buzzer (blind spot monitor buzzer)

·

Harness or connector


C1ABE Short to GND or Open in Buzzer Both of the following conditions are met:
·

Blind spot monitor main switch (warning cancel switch assembly) is on with ignition switch ON.

·

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.


·

Blind spot monitor sensor RH

·

Rear cross traffic alert buzzer (blind spot monitor buzzer)

·

Harness or connector



WIRING DIAGRAM

E254403E08
0.198,1.01 1.521,1.198 1.323,0.188 10 false from IG1 NO.2 Relay 2.24,1.177 2.792,1.365 0.552,0.188 10 false GAUGE 3.052,1.531 4.99,1.906 1.938,0.375 10 false Rear Cross Traffic Alert Buzzer (Blind Spot Monitor Buzzer) 5.177,2.115 7.094,2.313 1.917,0.198 10 false Blind Spot Monitor Sensor RH 3.052,1.354 3.344,1.531 0.292,0.177 10 false N34 5.177,1.958 5.385,2.146 0.208,0.188 10 false T1 5.656,1.01 5.979,1.198 0.323,0.188 10 false BUZ 3.51,1.021 3.833,1.208 0.323,0.188 10 false BZP 4.333,1.021 4.656,1.208 0.323,0.188 10 false BZN 3.313,0.906 3.521,1.094 0.208,0.188 10 false 1 4.688,0.917 4.896,1.104 0.208,0.188 10 false 2 5.448,0.917 5.656,1.104 0.208,0.188 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot main switch (warning cancel switch assembly*1 or telltale light assembly*2) is on.

*1: for LHD

*2: for RHD

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

b.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

DTCs are output

2.CHECK HARNESS AND CONNECTOR (REAR CROSS TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (REAR CROSS TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR RH)
a.

Disconnect the N34 rear cross traffic alert buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the T1 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N34-2 (BZN) - T1-3 (BUZ) Always Below 1 Ω
N34-2 (BZN) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N34-1 (BZP) - Body ground Ignition switch ON 11 to 14 V
N34-1 (BZP) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR CROSS TRAFFIC ALERT BUZZER (BLIND SPOT MONITOR BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK REAR CROSS TRAFFIC ALERT BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Replace the rear cross traffic alert buzzer (blind spot monitor buzzer).

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Clear DTCs
50002 314

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314

Result:
Proceed to
No DTCs are output
DTCs are output



No DTCs are output

END (REAR CROSS TRAFFIC ALERT BUZZER [BLIND SPOT MONITOR BUZZER] IS DEFECTIVE)

DTCs are output