Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › 2013.11–2015.10
RM3090E _52 Drivetrain _008760 GF1A TRANSFER / 4WD / AWD _0048749 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM J

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  4WD Warning Light Remains ON  


DESCRIPTION

The 4WD ECU assembly is connected to the combination meter assembly via the CAN communication system.

·

for Segment Display Type:

If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control 4WD/AWD system , the 4WD/AWD warning light comes on in the combination meter assembly.

·

for Dot Display Type:

If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control AWD system , the master warning light comes on and the warning message is displayed on the multi-information display in the combination meter assembly.


WIRING DIAGRAM

C278461E03
5.833,3.5 6.292,3.698 0.458,0.198 10 false G86 5.896,3.042 6.354,3.24 0.458,0.198 10 false GND 5.927,2.167 6.385,2.365 0.458,0.198 10 false IG1 5.667,2.031 5.875,2.229 0.208,0.198 10 false 3 5.656,2.917 5.906,3.094 0.25,0.177 10 false 4 4.792,2.313 5.896,2.5 1.104,0.188 10 false ECU-IG NO. 1 1.094,0.917 1.708,1.104 0.615,0.188 10 false CAN I/F 3.396,4.406 4.948,4.604 1.552,0.198 10 false from IG Circuit 3.385,4.948 4.938,5.146 1.552,0.198 10 false from Battery 5.823,3.656 7.156,3.865 1.333,0.208 10 false 4WD ECU Assembly 1.167,2.125 1.563,2.344 0.396,0.219 10 false CPU 0.5,3.49 0.875,3.948 0.375,0.458 10 false LED Driver 1.167,3.385 2.188,3.813 1.021,0.427 10 false Multi-information Display*2 0.365,4.625 2.385,4.823 2.021,0.198 10 false 4WD/AWD Warning Light*1 0.26,5.177 2.281,5.375 2.021,0.198 10 false Master Warning Light*2 1.01,6.417 3.031,6.615 2.021,0.198 10 false : CAN Communication System 4.01,5.948 6.031,6.146 2.021,0.198 10 false *1: for Segment Display Type 4.042,6.219 6.063,6.417 2.021,0.198 10 false *2: for Dot Display Type 3.375,2.156 4.469,2.354 1.094,0.198 10 false from IG1 Circuit 0.26,5.969 2.229,6.177 1.969,0.208 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM AND DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM)

b.

Check if the dynamic torque control 4WD/AWD system DTC is output.

Click hereDrivetrain>GF1A TRANSFER / 4WD / AWD>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118

Result:
Result Proceed to
Neither CAN communication system DTC nor dynamic torque control 4WD/AWD system DTC is output A
CAN communication DTC is output (for LHD) B
CAN communication DTC is output (for RHD) C
Dynamic torque control 4WD/AWD system DTC is output D


HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



A

2.CHECK IF 4WD ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

GO TO CAN COMMUNICATION (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION (HOW TO PROCEED WITH TROUBLESHOOTING)

D

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM)

2.CHECK IF 4WD ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the 4WD ECU assembly connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG (for 2AR-FE)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
NG (for 1AD-FTV)



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG (for 2AR-FE)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

NG (for 1AD-FTV)

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C06
2.385,0.104 2.792,0.365 0.406,0.26 1.938,1.927 2.24,1.927 2.24,1.927 2.333,1.177 true 1.677,1.854 2.021,2.052 0.344,0.198 10 IG1 2.49,0.146 2.802,0.344 0.313,0.198 10 G86 0,0 0.313,0.156 0.313,0.156 10 *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G86-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C270074C07
2.385,0.104 2.792,0.365 0.406,0.26 2.167,1.917 2.417,1.917 2.417,1.917 2.583,1.167 true 1.833,1.833 2.177,2.031 0.344,0.198 10 GND 2.49,0.146 2.802,0.344 0.313,0.198 10 G86 0,0 0.313,0.156 0.313,0.156 10 *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (4WD WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (4WD WARNING LIGHT)
a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


g.

According to the display on the GTS, read the Data List.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
4WD Warning Light 4WD/AWD warning Light*1
AWD warning*2
OFF or ON OFF: Warning light off*1
OFF: Warning off*2
ON: Warning light on*1
ON: Warning on*2
-

*1: for Segment Display Type

*2: for Dot Display Type


Chassis > Four Wheel Drive > Data List
Tester Display
4WD Warning Light
50003 118 7

h.

Check the GTS diplay condition of the 4WD/AWD warning light.


Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON



Display of the Data List remains OFF

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

Display of the Data List remains ON