Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2014.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046951 CYLINDER HEAD G

3ZR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER HEAD FOR FLATNESS

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cylinder block and manifolds.

A297846C01
3.083,0.51 3.396,0.667 0.313,0.156 10 *a 5.104,0.427 5.417,0.583 0.313,0.156 10 *b 5.104,1.344 5.417,1.5 0.313,0.156 10 *c
*a Cylinder Head Lower Side *b Intake Manifold Side
*c Exhaust Manifold Side - -


Maximum Warpage:
Item Specified Condition
Cylinder head lower side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold side 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If cracked, replace the cylinder head.


Hide 3.INSPECT VALVE SEATS

a.
A146287C14
2.958,1.26 3.271,1.417 0.313,0.156 10 false *1
*1 Width


Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Intake Side:

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).

If not, correct the valve seat.


ii.

Exhaust Side:

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).

If not, correct the valve seat.


iii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 4.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Install the camshaft.

Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

HINT:

Do not use seal packing when installing the camshaft housing sub-assembly, as the installation is temporary.



b.
A150953

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.06 to 0.155 mm (0.00236 to 0.00610 in.)


Maximum thrust clearance:

0.17 mm (0.00669 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly. If the thrust surface is damaged, replace the camshaft.


Hide 5.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the bearing caps and camshaft journals.


b.

Place the camshafts on the camshaft housing sub-assembly.

HINT:

Do not use seal packing when installing the camshaft housing sub-assembly, as the installation is temporary.



c.
A150965C05
0.744,0.094 0.907,0.273 0.163,0.18 10 *1 0.949,0.182 1.061,0.182 1.061,0.182 1.785,1.012 false
*1 Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

NOTICE:

Do not turn the camshaft.



e.

f.
A150954C05
0.718,0.123 0.886,0.311 0.168,0.188 10 *1 0.904,0.199 1.054,0.199 1.054,0.199 1.871,1.022 false
*1 Plastigage


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
Camshaft No. 1 Journal 0.030 to 0.063 mm (0.00118 to 0.00248 in.)
Camshaft Other Journals 0.035 to 0.072 mm (0.00138 to 0.00283 in.)


Maximum Oil Clearance:
Item Specified Condition
Camshaft No. 1 Journal 0.085 mm (0.00335 in.)
Camshaft Other Journals 0.09 mm (0.00354 in.)


NOTICE:

Completely remove the Plastigage after the inspection.


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.


Hide 13711B 6.INSPECT COMPRESSION SPRING

a.
A333833

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

51.9 mm (2.04 in.)


If the free length is not as specified, replace the compression spring.


b.
A319225C09
1.458,0.406 1.771,0.563 0.313,0.156 10 false *1 0.969,1.417 1.281,1.573 0.313,0.156 10 false *a
*1 Deviation
*a 37.5 mm (1.48 in.)


Using a steel square, measure the deviation of the compression spring.

Maximum deviation:

1.3 mm (0.0512 in.)


If the deviation is more than the maximum, replace the compression spring.


Hide 13711 7.INSPECT INTAKE VALVE

a.

Using a vernier caliper, measure the overall length of the intake valve.

Standard overall length:

109.34 mm (4.30 in.)


Minimum overall length:

108.84 mm (4.29 in.)


If the overall length is less than the minimum, replace the intake valve.


b.

Using a micrometer, measure the diameter of the valve stem.

Valve stem diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


If the valve stem diameter is not as specified, check the oil clearance.


c.
A297848C01
0.521,1.771 0.833,1.927 0.313,0.156 10 *1
*1 Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the intake valve.


Hide 13715 8.INSPECT EXHAUST VALVE

a.

Using a vernier caliper, measure the overall length of the exhaust valve.

Standard overall length:

108.25 mm (4.26 in.)


Minimum overall length:

107.75 mm (4.24 in.)


If the overall length is less than the minimum, replace the exhaust valve.


b.

Using a micrometer, measure the diameter of the valve stem.

Valve stem diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


If the valve stem diameter is not as specified, check the oil clearance.


c.
A121382C21
0.344,1.833 0.656,1.99 0.313,0.156 10 *1
*1 Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


Hide 9.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A150966

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bushing inside diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.080 mm (0.00315 in.)
Exhaust 0.085 mm (0.00335 in.)


If the clearance is more than the maximum, replace the valve and guide bush.