Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › ENGINE UNIT › 2014.10–2015.10
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046950 ENGINE UNIT A

3ZR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A150846

Remove the oil filler cap sub-assembly.


Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A128159

Remove the oil filler cap gasket.


Hide 12635 3.REMOVE ENGINE COVER JOINT

a.
A150847

Remove the 2 engine cover joints.


Hide 11101W 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11101J 7.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11401G 9.REMOVE CRANKSHAFT POSITION SENSOR

Hide 83530 10.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 12.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11201 13.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A150850

Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.


b.
A150852

Remove the 3 gaskets from the camshaft bearing cap.

NOTICE:

As gaskets may stick to the cylinder head cover, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover.



Hide 11213 14.REMOVE CYLINDER HEAD COVER GASKET

a.
A150851

Remove the cylinder head cover gasket.


Hide 11193 15.REMOVE SPARK PLUG TUBE GASKET

a.
A152586

Pry up the 4 claws of the ventilation baffle plate.

NOTICE:

Do not deform the claws of the ventilation baffle plate more than necessary.



b.
A337770

Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from cylinder head cover sub-assembly.

NOTICE:
·

As much as possible prevent the spark plug tube gaskets from being deformed.

·

Do not damage the spark plug tube gasket and cylinder head cover sub-assembly.

·

Make sure not to damage the spark plug tube gasket and cylinder head cover sub-assembly when inserting the screwdriver in the joint area.



HINT:

If the cylinder head cover sub-assembly is damaged, smooth the surface with 400-grid sandpaper.



Hide 15620 16.REMOVE OIL FILTER CAP ASSEMBLY

Hide 17.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A234710C02
1.229,1.76 1.885,2.365 1.885,2.365 2.521,1.802 true 1.292,3.115 0.479,3.271 true 1.208,3.281 0.781,3.813 true 1.792,2.406 2.073,2.625 0.281,0.219 10 *1 0.24,3.198 0.521,3.427 0.281,0.229 10 *1 0.615,3.833 0.896,4.073 0.281,0.24 10 *2
*1 Timing Mark
*2 Timing Notch


Turn the crankshaft pulley until its timing notch and timing mark "0" of the timing chain cover are aligned.


b.

Check that the timing marks on both the camshaft timing exhaust gear and camshaft timing gear are facing upward as shown in the illustration.

HINT:

If the marks are not as shown, turn the crankshaft 1 complete revolution (360°) and align the marks as specified above.



Hide 13540 19.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A250765

Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner assembly installed.



Hide 20.REMOVE ENGINE MOUNTING BRACKET STUD BOLT

a.
A211980

Remove the engine mounting bracket stud bolt.


Hide 11302 21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 22.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 16323 23.REMOVE WATER INLET HOUSING

a.
A150906

Remove the 3 bolts, water inlet housing and gasket.


Hide 12511 24.REMOVE NO. 1 GENERATOR BRACKET

a.
A150905

Remove the 4 bolts and No. 1 generator bracket.


Hide 13559 25.REMOVE CHAIN TENSIONER SLIPPER

A150870

Hide 13561 26.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A165280

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 27.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13506 28.REMOVE CHAIN SUB-ASSEMBLY

a.
A251821C01
2.677,1.99 2.875,1.271 2.875,1.271 3.01,1.271 true 1.375,3.76 1.552,3.323 1.552,3.323 1.635,3.323 true 1.74,0.052 1.969,0.26 0.229,0.208 10 *a 3.052,1.188 3.365,1.417 0.313,0.229 10 *b 1.646,3.229 1.917,3.469 0.271,0.24 10 *c
*a Turn
*b Place the Chain on the Gear
*c Loosen the Chain


Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing gears.


b.

With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear assembly and place it on the camshaft timing gear assembly.

HINT:

Be sure to release the chain sub-assembly from the sprocket completely.



c.

Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.


Hide 13521 29.REMOVE CRANKSHAFT TIMING SPROCKET

Hide 13507 30.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 19315 31.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 13521A 32.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A150909C07
0.672,0.666 0.837,0.828 0.165,0.162 10 *1 0.857,0.763 0.964,0.763 0.964,0.763 1.178,1.335 false
*1 Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys.

HINT:

Tape the screwdriver tip before use.



Hide 13050 33.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 34.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 35.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 36.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 37.REMOVE CAMSHAFT BEARING CAP

Hide 13512 39.REMOVE NO. 2 CAMSHAFT

Hide 13801 40.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A332534

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 41.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A297858

Remove the 16 valve lash adjuster assemblies from the cylinder head.

HINT:

Arrange the removed parts in the correct order.



Hide 15678A 42.REMOVE OIL CONTROL VALVE FILTER

a.
A150883

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 43.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 44.REMOVE NO. 2 CAMSHAFT BEARING

Hide 11103 45.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13716 46.REMOVE VALVE STEM CAP

a.
A150945

Remove the 16 valve stem caps.

HINT:

Arrange the removed parts in the correct order.



Hide 11114A 47.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 11101 48.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 12204 50.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 12101A 51.REMOVE OIL PAN DRAIN PLUG

a.
A150893

Remove the oil pan drain plug and gasket.


Hide 12102A 52.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15100 53.REMOVE OIL PUMP ASSEMBLY

Hide 11420 55.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A150897

Uniformly loosen and remove the 11 bolts.


b.
A150898C09
0.448,3.083 0.604,3.49 0.604,3.49 0.604,3.615 true 1.177,3.573 1.344,3.979 1.344,3.979 1.344,4.104 true 2.479,3.396 2.646,3.802 2.646,3.802 2.646,3.927 true 3.083,2.688 3.25,3.083 3.25,3.083 3.25,3.208 true 0.521,3.646 0.719,3.833 0.198,0.188 10 *1 1.25,4.135 1.448,4.323 0.198,0.188 10 *1 2.552,3.938 2.75,4.125 0.198,0.188 10 *1 3.167,3.25 3.365,3.438 0.198,0.188 10 *1
*1 Protective Tape


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase and cylinder block.

NOTICE:

Be careful not to damage the contact surfaces of the stiffening crankcase and cylinder block.


HINT:

Tape the screwdriver tip before use.



Hide 11432A 56.REMOVE NO. 1 TAPER SCREW PLUG

a.
A300838

Remove the No. 1 taper screw plug.


Hide 57.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 58.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.