Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL TANK(w/ Canister Pump Module) › from 2014.10
RM3090E _51 Engine / Hybrid System _008397 2AR-FE FUEL _0056278 FUEL TANK(w/ Canister Pump Module) A

2AR-FE FUEL  FUEL TANK(w/ Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 77643A 1.INSTALL NO. 3 FUEL TANK PROTECTOR

a.

Install a new No. 3 fuel tank protector to the fuel tank assembly.


Hide 77202 2.INSTALL BREATHER TUBE SUB-ASSEMBLY

a.

Install the breather tube sub-assembly to the fuel tank assembly and connect the quick connector.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION


Hide 77295D 3.INSTALL FUEL TUBE GROMMET

a.

Install the 3 fuel tube grommets to the fuel tank assembly.


Hide 77299A 4.INSTALL NO. 5 FUEL TUBE CLAMP

a.

Install the No. 5 fuel tube clamp to the fuel tank assembly.


Hide 77289B 5.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the No. 3 fuel tube clamp to the fuel tank assembly.


Hide 77209D 6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Install the fuel tank main tube sub-assembly and attach the 5 clamps.


Hide 83320 7.INSTALL FUEL SENDER GAUGE ASSEMBLY

Hide 8.INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP

Hide 77168A 9.INSTALL FUEL TANK VENT TUBE SET PLATE

Hide 77209D 10.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77100 11.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter with attachments.


b.

Lift up the engine lifter.


c.

Attach the wire harness to the 3 clamps.


d.

Connect the fuel pump connector and sender gauge connector.

NOTICE:

Be careful not to cut the wiring.



e.

Install the No. 1 fuel tank band sub-assembly with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


f.

Install the No. 1 fuel tank band sub-assembly LH with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


g.

Install the No. 2 fuel tank band sub-assembly with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


h.

Attach the 3 wire harness clamps and connect the connector.


Hide 77202 12.CONNECT BREATHER TUBE SUB-ASSEMBLY

a.

Connect the breather tube sub-assembly to the fuel tank filler pipe.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION


Hide 77404 13.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

a.

Attach the hose clamp and fuel tank vent hose sub-assembly.


Hide 77213E 14.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A201331C01
2.375,3.354 2.375,3.208 2.375,3.208 2.698,2.792 true 1.948,3.885 1.813,3.885 1.813,3.885 1.552,2.99 false 0.354,3.427 0.635,3.604 0.281,0.177 10 90° 1.052,3.26 1.333,3.438 0.281,0.177 10 45° 0.75,3.771 1.063,3.927 0.313,0.156 10 *1 2,3.813 2.313,3.969 0.313,0.156 10 *2 2.323,3.385 2.635,3.542 0.313,0.156 10 *3 0.667,1.979 0.979,2.135 0.313,0.156 10 *a 2.385,2.323 2.698,2.479 0.313,0.156 10 *b
*1 Range
*2 Stopper
*3 Protrusion
*a Top of Vehicle
*b Bottom of Fuel Tank


Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the hose clamp.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 77276 15.INSTALL FUEL HOSE PROTECTOR

a.

Install the fuel hose protector to the fuel tank to filler pipe hose and attach the claw.


Hide 77019J 16.CONNECT FUEL TANK TO CANISTER TUBE SUB-ASSEMBLY

a.

Connect the fuel tank to canister tube sub-assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION


Hide 77209D 17.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION


Hide 58398F 18.INSTALL NO. 1 FLOOR UNDER COVER

a.

Install the No. 1 floor under cover with the 2 nuts and attach the clip.


Hide 50819 20.INSTALL FRONT FLOOR COVER

a.

Install the front floor cover and attach the 5 clips.


b.

Install the bolt and nut.

Torque:
for bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)
for nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 21.CONNECT PARKING BRAKE CABLE

a.

Connect the parking brake cable with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 22.ADD FUEL

Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION