Home › Engine / Hybrid System › 3ZR-FAE FUEL › FUEL TANK › from 2014.10
RM3090E _51 Engine / Hybrid System _008388 3ZR-FAE FUEL _0046822 FUEL TANK A

3ZR-FAE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.DRAIN FUEL

Hide 5.DISCONNECT PARKING BRAKE CABLE

a.
A293546

Remove the 2 bolts and disconnect the parking brake cable.


Hide 50819 6.REMOVE FRONT FLOOR COVER

a.
A332503

Remove the bolt and nut.


b.

Detach the 5 clips and remove the front floor cover.


Hide 77641A 7.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A271431

Detach the 3 clips and remove the nut and No. 1 fuel tank protector.


Hide 58398F 8.REMOVE NO. 1 FLOOR UNDER COVER

a.
A271432

Detach the clip and remove the 2 nuts and No. 1 floor under cover.


Hide 77026A 9.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A293550

Slide the clamp and disconnect the No. 1 fuel evaporation tube sub-assembly.


Hide 77209D 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A293551

Disconnect the fuel tank main tube sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION


Hide 77276 11.REMOVE FUEL HOSE PROTECTOR

A199132

a.

Detach the claw and remove the fuel hose protector from the fuel tank to filler pipe hose.


Hide 77213E 12.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A173328

Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77707 13.DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A293554

Detach the hose clamp.


b.
A293552

Slide the clamp and disconnect the charcoal canister outlet tube sub-assembly from the fuel tank breather tube.


Hide 77014A 14.DISCONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A293553

Disconnect the No. 3 fuel tank breather tube sub-assembly from the fuel tank assembly.

Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION


Hide 77100 15.REMOVE FUEL TANK ASSEMBLY

a.
A293577

Detach the 3 wire harness clamps.


b.

Using an engine lifter and attachments, support the fuel tank assembly.


c.
A293555

Remove the 2 bolts and No. 1 fuel tank band sub-assembly.


d.

Remove the 2 bolts and No. 1 fuel tank band sub-assembly LH.


e.

Remove the 2 bolts and No. 2 fuel tank band sub-assembly.


f.

Slightly lower the engine lifter.

NOTICE:

Be careful not to cut the wiring.



g.
A297843

Disconnect the fuel pump connector and sender gauge connector.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




h.

Detach the wire harness from the 3 clamps and remove the fuel tank assembly.


Hide 16.DISCONNECT FUEL EMISSION HOSE

Hide 77209D 17.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77168A 18.REMOVE FUEL TANK VENT TUBE SET PLATE

Hide 19.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP

Hide 83320 20.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 77209D 21.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

A299336

a.

Detach the 5 clamps and remove the fuel tank main tube sub-assembly.


Hide 77026A 22.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Detach the 5 clamps and remove the No. 1 fuel evaporation tube sub-assembly.


Hide 77289B 23.REMOVE NO. 3 FUEL TUBE CLAMP

a.

Remove the No. 3 fuel tube clamp from the fuel tank assembly.


Hide 77299A 24.REMOVE NO. 5 FUEL TUBE CLAMP

a.

Remove the No. 5 fuel tube clamp from the fuel tank assembly.


Hide 77295D 25.REMOVE FUEL TUBE GROMMET

a.

Remove the 3 fuel tube grommets from the fuel tank assembly.


Hide 77707 26.REMOVE CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A293558

Detach the 2 clamps and remove the canister outlet tube sub-assembly from the fuel tank assembly.


Hide 27.REMOVE FUEL EMISSION HOSE

a.
A293559C01
0.75,1.115 0.75,0.917 0.75,0.917 2.917,0.917 true 1.115,1.115 1.115,0.917 false 2.938,0.833 3.25,0.99 0.313,0.156 10 *1
*1 Retainer


Pinch the retainer as shown in the illustration, and then remove the fuel emission hose.

NOTICE:
·

Clean off any dirt and foreign matter from the clip before disconnecting the hoses.

·

Do not use any tools in this procedure.

·

Do not forcefully bend or twist the nylon tube.

·

Put the hose in a plastic bag to prevent damage and contamination.

·

If the connector is stuck, pinch the retainer and push and pull the hose to disconnect it.