Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD) › 2014.10–2015.10
RM3090E _52 Drivetrain _008761 DRIVE SHAFT / PROPELLER SHAFT _0050236 FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 4WD/AWD)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 43410C 1.INSTALL FRONT DRIVE SHAFT BEARING (for RH Side)

a.
C278916N01
0.458,1.875 0.958,1.875 0.958,1.875 1.115,1.656 true 0.479,0.313 0.75,0.313 0.75,0.313 0.885,0.563 true 0.167,0.24 0.625,0.438 0.458,0.198 10 SST 0.156,1.771 0.615,1.969 0.458,0.198 10 SST

Using SST and a press, install a new front drive shaft bearing to the front drive inboard joint assembly RH.

SST
09527-10011  
09710-30012  (09710-04081)

NOTICE:
·

Make sure the front drive shaft bearing contacts the edge of the front drive inboard joint assembly RH, but do not press it in more than necessary.

·

Do not apply weight to the dust cover and outer race of the front drive shaft bearing.




b.
C127665

Using a snap ring expander, install a new snap ring.

NOTICE:

The Snap ring should be installed completely.



Hide 41336E 2.INSTALL FRONT DRIVE SHAFT DUST COVER LH

a.
C127677N01
0.656,0.656 0.552,0.313 0.552,0.313 0.427,0.313 true 0.094,0.219 0.385,0.375 0.292,0.156 10 SST

Using SST and a press, press in the front drive inboard joint assembly LH until the new front drive shaft dust cover LH contacts the edge of the front drive inboard joint assembly LH.

SST
09527-10011  

NOTICE:
·

Make sure to install the front drive shaft dust cover LH in the correct direction.

·

Do not damage the front drive shaft dust cover LH.

·

The front drive shaft dust cover LH should be installed completely.




Hide 41336D 3.INSTALL FRONT DRIVE SHAFT DUST COVER RH

a.
C166793N04
0.5,0.917 0.5,0.583 0.5,0.583 0.365,0.583 true 0.063,0.51 0.521,0.708 0.458,0.198 10 SST 1.76,4.104 2.219,4.302 0.458,0.198 10 (A)

Using SST and a press, install a new front drive shaft dust cover RH to the front drive inboard joint assembly RH until the distance from the tip of the front drive inboard joint assembly RH to the front drive shaft dust cover RH onto reaches the specification as shown in the illustration.

SST
09527-10011  

Standard Distance (A):

103.5 to 104.5 mm (4.075 to 4.114 in.)


NOTICE:
·

Make sure to install the front drive shaft dust cover RH in the correct direction.

·

Do not damage the front drive shaft dust cover RH.

·

Front drive shaft dust cover RH should be installed completely.




Hide 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C127681C05
2.094,0.479 1.896,0.479 1.896,0.479 1.76,0.75 false 2.146,0.406 2.833,0.573 0.688,0.167 10 false *a
*a Protective Tape


Before installing the front axle outboard joint boot, wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the front axle outboard joint boot from being damaged.


b.
C274280C02
1.667,1.719 1.667,1.427 true 2.333,1.708 2.333,1.313 true 2.99,1.479 2.99,1.177 true 1.604,1.75 1.917,1.906 0.313,0.156 10 false *1 2.271,1.792 2.583,1.948 0.313,0.156 10 false *2 2.927,1.521 3.24,1.677 0.313,0.156 10 false *3
*1 Front No. 2 Axle Outboard Joint Boot Clamp
*2 Front Axle Outboard Joint Boot
*3 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the front drive outboard joint shaft assembly in the following order.

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Install the front axle outboard joint boot so that it is between the front No. 2 axle outboard joint boot clamp and front drive outboard joint shaft assembly.


d.

Temporarily install the front axle outboard joint boot clamp to the front axle outboard joint boot.


e.

Pack the front drive outboard joint shaft assembly and front axle outboard joint boot with grease from the boot kit.

Standard Grease Capacity:
Item Grease Capacity
for 2AD-FTV, 2AD-FHV (Automatic Transaxle) 205 to 215 g (7.3 to 7.5 oz)
for 1AD-FTV, 2AD-FTV, 2AD-FHV (Manual Transaxle)
for 2AR-FE (Automatic Transaxle)
for 2AR-FE (Manual Transaxle)
for 3ZR-FE, 3ZR-FAE (Manual Transaxle)
for 3ZR-FE, 3ZR-FAE (CVT) 171 to 181 g (6.1 to 6.3 oz)



f.

Install the front axle outboard joint boot to the groove of the front drive outboard joint shaft assembly.

NOTICE:
·

Do not apply grease to the part of the front axle outboard joint boot that contacts the groove.

·

Do not allow foreign matter to enter the front axle outboard joint boot.




Hide 43447F 5.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

C107943

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.

Install the front No. 2 axle outboard joint boot clamp LH onto the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly and install the front No. 2 axle outboard joint boot clamp LH as close to the inside of the vehicle as possible.

·

Check the band and lever for any deformation before folding back the lever.




b.
C127684

Lean your weight on your hand and roll the front drive outboard joint shaft assembly LH forward while pressing the front drive outboard joint shaft assembly LH against a surface until a click sound is heard.

NOTICE:
·

Do not damage the deflector.

·

Make sure that the front drive outboard joint shaft assembly LH is in direct contact with the surface.




c.
C127685

Using a plastic-faced hammer, tap the buckle to fix the lever in place while making sure that the end of the lever is even with the edge of the buckle.

NOTICE:

Do not damage the front axle outboard joint boot.



Hide 43447D 6.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43447E 7.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

C129510

CAUTION:

Wear protective gloves to avoid injuries to your hands.


a.

Install the front axle outboard joint boot clamp LH to the front axle outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and lever for any deformation before folding back the lever.




b.
C129511

Using water pump pliers, pinch the front axle outboard joint boot clamp LH to temporarily fix it in place.


c.
C129512

Using a plastic-faced hammer, tap the buckle to fix the lever in place while making sure that the end of the lever is even with the edge of the buckle.

NOTICE:

Do not damage the front axle outboard joint boot.



Hide 43447C 8.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43474E 9.INSTALL FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)

a.

w/ 1 Clamp:

i.
C307747C01
1.438,4.083 1.271,4.083 1.271,4.083 1.271,3.635 true 0.865,1.833 0.698,1.833 0.698,1.833 0.698,1.25 true 0.823,4.292 0.656,4.292 0.656,4.292 0.656,3.677 true 1.406,1.698 1.24,1.698 1.24,1.698 1.24,1.281 true 0.125,0.115 0.438,0.313 0.313,0.198 10 false *A 0.135,2.375 0.448,2.573 0.313,0.198 10 false *a 1.417,2.521 1.729,2.719 0.313,0.198 10 false (A) 1.5,4.01 1.823,4.208 0.323,0.198 10 false *1 1.469,0.313 1.781,0.51 0.313,0.198 10 false (A) 1.49,1.625 1.854,1.844 0.365,0.219 10 false *1 0.927,1.76 1.313,1.969 0.385,0.208 10 false *2 0.885,4.219 1.26,4.396 0.375,0.177 10 false *2
*A for 3ZR-FE, 3ZR-FAE
*1 Front Drive Shaft Damper Clamp LH
*2 Front Drive Shaft Damper LH
*a except 3ZR-FE, 3ZR-FAE


Install a new front drive shaft damper clamp LH and front drive shaft damper LH onto the front drive outboard joint shaft assembly LH.

HINT:

Make sure the front drive shaft damper clamp LH is on the outboard joint side.



ii.

Adjust the position of the drive shaft damper LH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):
Item Length
for 3ZR-FE, 3ZR-FAE 199.0 to 203.0 mm (7.835 to 7.992 in.)
except 3ZR-FE, 3ZR-FAE 212.5 to 216.5 mm (8.367 to 8.523 in.)




b.

w/ 2 Clamps:

i.
C307748C01
0.229,1.615 0.229,1.281 true 0.813,1.625 0.813,1.292 true 1.354,1.615 1.354,1.281 true 0.219,3.948 0.219,3.615 true 0.781,4 0.781,3.667 true 1.365,3.938 1.365,3.604 true 0.188,1.677 0.5,1.875 0.313,0.198 10 false *1 0.771,1.677 1.083,1.875 0.313,0.198 10 false *2 0.052,0.031 0.406,0.271 0.354,0.24 10 false *A 0.104,2.438 0.458,2.677 0.354,0.24 10 false *a 1.313,1.688 1.625,1.885 0.313,0.198 10 false *1 0.167,4.021 0.479,4.219 0.313,0.198 10 false *1 0.719,4.073 1.031,4.271 0.313,0.198 10 false *2 1.313,4.021 1.625,4.219 0.313,0.198 10 false *1 1.479,2.552 1.792,2.75 0.313,0.198 10 false (A) 1.521,0.344 1.833,0.542 0.313,0.198 10 false (A)
*A for 3ZR-FE, 3ZR-FAE
*1 Front Drive Shaft Damper Clamp LH
*2 Front Drive Shaft Damper LH
*a except 3ZR-FE, 3ZR-FAE


Install 2 new front drive shaft damper clamp LH and the front drive shaft damper LH onto the front drive outboard joint shaft assembly LH.


ii.

Adjust the position of the drive shaft damper LH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):
Item Length
for 3ZR-FE, 3ZR-FAE 199.0 to 203.0 mm (7.835 to 7.992 in.)
except 3ZR-FE, 3ZR-FAE 212.5 to 216.5 mm (8.367 to 8.523 in.)




Hide 43474D 10.INSTALL FRONT DRIVE SHAFT DAMPER RH

a.

w/ 1 Clamp:

i.
C307750C01
0.833,1.667 0.833,1.25 true 1.354,1.667 1.354,1.25 true 1.313,1.729 1.625,1.927 0.313,0.198 10 false *1 0.792,1.729 1.104,1.927 0.313,0.198 10 false *2 1.583,0.302 2.042,0.5 0.458,0.198 10 false (A)
*1 Front Drive Shaft Damper Clamp RH
*2 Front Drive Shaft Damper RH


Install a new front drive shaft damper clamp RH and front drive shaft damper RH onto the front drive outboard joint shaft assembly RH.

HINT:

Make sure the front drive shaft damper clamp RH is on the outboard joint side.



ii.

Adjust the position of the drive shaft damper RH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):

199.0 to 203.0 mm (7.835 to 7.992 in.)




b.

w/ 2 Clamps:

i.
C307749C01
0.219,1.646 0.219,1.229 true 0.813,1.656 0.813,1.24 true 1.344,1.656 1.344,1.24 true 0.156,1.688 0.469,1.885 0.313,0.198 10 false *1 0.771,1.729 1.083,1.927 0.313,0.198 10 false *2 1.292,1.698 1.604,1.896 0.313,0.198 10 false *1 1.542,0.323 2,0.521 0.458,0.198 10 false (A)
*1 Front Drive Shaft Damper Clamp RH
*2 Front Drive Shaft Damper RH


Install 2 new front drive shaft damper clamp RH and the front drive shaft damper RH onto the front drive outboard joint shaft assembly RH.


ii.

Adjust the position of the drive shaft damper RH so that the distance shown in the illustration is within the specified range.

Standard Distance (A):

199.0 to 203.0 mm (7.835 to 7.992 in.)




Hide 43474G 11.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ Drive Shaft Damper)

a.
C127651C02
0.438,4.135 0.594,4.281 0.594,4.281 0.771,4.281 true 0.063,0.031 0.271,0.198 0.208,0.167 10 false *A 0.073,2.292 0.302,2.469 0.229,0.177 10 false *B 0.844,4.198 1.073,4.375 0.229,0.177 10 false *a
*A for One Touch Type
*B for Claw Engagement Type
*a Claw Engagement


w/ 1 Clamp:

Install the front drive shaft damper clamp LH.

NOTICE:

Be sure to install the front drive shaft damper clamp LH in the correct position.


i.

for One Touch Type:

Using a screwdriver, install the front drive shaft damper clamp LH as shown in the illustration.


ii.

for Claw Engagement Type:

Using needle-nose pliers, install the front drive shaft damper clamp LH as shown in the illustration.

NOTICE:

Do not deform the claw engagement of the front drive shaft damper clamp LH.




b.
C127651C02
0.438,4.135 0.594,4.281 0.594,4.281 0.771,4.281 true 0.063,0.031 0.271,0.198 0.208,0.167 10 false *A 0.073,2.292 0.302,2.469 0.229,0.177 10 false *B 0.844,4.198 1.073,4.375 0.229,0.177 10 false *a
*A for One Touch Type
*B for Claw Engagement Type
*a Claw Engagement


w/ 2 Clamps:

Install the 2 front drive shaft damper clamp LH.

NOTICE:

Be sure to install the front drive shaft damper clamp LH in the correct position.


i.

for One Touch Type:

Using a screwdriver, install the 2 front drive shaft damper clamp LH as shown in the illustration.


ii.

for Claw Engagement Type:

Using needle-nose pliers, hold the 2 front drive shaft damper clamp LH at the claw engagement.

NOTICE:

Do not deform the claw engagement of the front drive shaft damper clamp LH.




Hide 43474F 12.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43040 13.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp LH
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp LH
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the front drive outboard joint shaft assembly LH in the following order.

i.

Front axle inboard joint boot clamp LH


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp LH



b.

Remove the protective tape from the front drive outboard joint shaft assembly LH.


c.
C127694C02
1.927,1.188 2.083,1.833 2.083,1.833 1.365,1.531 true 2.083,1.833 2.25,1.833 false 2.313,1.729 3.042,1.896 0.729,0.167 10 *a
*a Matchmark


Align the matchmarks and place the beveled side of the tripod joint axial spline toward the front drive outboard joint shaft assembly LH.

NOTICE:

Face the cut edge of the spline toward the inboard joint side and insert the spline onto the outboard joint shaft assembly LH.



d.
C104525

Using a brass bar and hammer, tap the tripod joint onto the front drive outboard joint shaft assembly LH.

NOTICE:
·

Do not tap the rollers.

·

Be sure to install the tripod in the correct direction.




e.
C127695

Using a snap ring expander, install a new snap ring.

NOTICE:

The Snap ring should be installed completely.



f.

Pack the front drive inboard joint assembly LH and front axle inboard joint boot with grease from the boot kit.

Standard grease capacity:

175 to 185 g (6.2 to 6.5 oz)



g.
C127646C05
1.833,0.833 1.833,0.25 true 2.167,0.396 2.167,0.25 2.167,0.25 1.417,0.25 true 1.188,0.167 1.5,0.365 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly LH to the front drive outboard joint shaft assembly LH.


Hide 43030 14.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL FRONT AXLE INBOARD JOINT BOOT

HINT:

Use the same procedure for the RH and LH sides.


a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.

NOTICE:
·

Do not apply grease to the part of the front axle inboard joint boot that contacts the groove.

·

Do not allow foreign matter to enter the front axle inboard joint boot.




b.
C278922C01
0.094,0.083 0.406,0.281 0.313,0.198 10 *A 0.094,1.854 0.406,2.052 0.313,0.198 10 *B 1.531,1.573 1.844,1.771 0.313,0.198 10 (A) 1.594,3.104 1.906,3.302 0.313,0.198 10 (A)
*A for LH Side
*B for RH Side


Check that the front axle inboard joint boot and front axle outboard joint boot are not stretched or contracted when the rear drive shaft assembly is at the standard length.

Length (A):
Item Length
for 2AD-FTV, 2AD-FHV (Automatic Transaxle) LH Side 565.6 mm (1.86 ft.)
RH Side 928.4 mm (3.05 ft.)
for 1AD-FTV, 2AD-FTV, 2AD-FHV (Manual Transaxle) LH Side 553.6 mm (1.82 ft.)
RH Side 933.9 mm (3.06 ft.)
for 2AR-FE (Automatic Transaxle) LH Side 577.6 mm (1.89 ft.)
RH Side 922.4 mm (3.03 ft.)
for 2AR-FE (Manual Transaxle) LH Side 583.6 mm (1.91 ft.)
RH Side 909.4 mm (2.98 ft.)
for 3ZR-FE, 3ZR-FAE (Manual Transaxle) LH Side 594.6 mm (1.95 ft.)
RH Side 896.4 mm (2.94 ft.)
for 3ZR-FE (CVT) LH Side 591.2 mm (1.94 ft.)
RH Side 881.9 mm (2.89 ft.)
for 3ZR-FAE (CVT) LH Side 591.2 mm (1.94 ft.)
RH Side 893.0 mm (2.93 ft.)


NOTICE:

Keep the drive shaft assembly level during inspection.


If the front axle inboard joint boot and front axle outboard joint boot are stretched or contracted, correct them.


Hide 43448F 16.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP LH

C127696C03
0.406,3.24 0.563,3.344 0.563,3.344 0.729,3.344 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *A 0.104,2.208 0.365,2.375 0.26,0.167 10 false *B 0.833,3.25 1.094,3.417 0.26,0.167 10 false *a
*A for One Touch Type
*B for Claw Engagement Type
*a Claw Engagement


a.

for One Touch Type:

Using a screwdriver, install the front axle inboard joint boot clamp LH as shown in the illustration.

NOTICE:
·

Correctly set the front No. 2 axle inboard joint boot clamp LH to the guide groove.

·

Do not damage the front axle inboard joint boot.




b.

for Claw Engagement Type:

i.

Install the front No. 2 axle inboard joint boot clamp LH to the drive shaft inboard joint boot.

NOTICE:

Correctly set the front No. 2 axle inboard joint boot clamp LH to the guide groove.



ii.

Using needle-nose pliers, hold the front No. 2 axle inboard joint boot clamp LH at the claw engagement.

NOTICE:
·

Do not damage the front axle inboard joint boot.

·

Do not deform the claw engagement of the front No. 2 axle inboard joint boot clamp LH.





Hide 43448C 17.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 43448G 18.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

HINT:

Use the same procedure described for the front axle inboard joint boot clamp LH.


Hide 43448E 19.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.