Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008756 EA64F MANUAL TRANSMISSION / TRANSAXLE _0048565 DIFFERENTIAL CASE A

EA64F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 43410M 1.REMOVE FRONT DIFFERENTIAL CASE OIL SEAL

a.
C318249N01
0.896,1.896 1.156,1.896 1.156,1.896 1.458,2.125 false 0.563,1.833 1.021,2.031 0.458,0.198 10 false SST

Using SST, remove the front differential case oil seal from the front differential case.

SST
09308-00010  


Hide 41311E 2.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C278047C01
2.135,1.052 2.698,1.052 false 2.865,0.302 3.177,0.5 0.313,0.198 10 false *a 0.417,0.427 0.729,0.625 0.313,0.198 10 true *b 2.813,0.938 3.271,1.135 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case front tapered roller bearing from the front differential case.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00560)


Hide 41311F 3.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C278048C01
2.188,1.198 2.531,1.198 false 0.26,0.573 0.573,0.771 0.313,0.198 10 false *b 2.896,0.354 3.208,0.552 0.313,0.198 10 false *a 2.604,1.135 3.063,1.333 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the front differential case rear tapered roller bearing from the front No. 1 differential case sub-assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00490)


Hide 41221 4.REMOVE FRONT DIFFERENTIAL RING GEAR

a.

Mount the front differential ring gear in a vise between aluminum plates.

NOTICE:
·

Be careful not to damage the front differential ring gear.

·

Do not overtighten the vise.




b.
C318251C01
1.938,0.604 2.479,0.927 2.479,0.927 1.802,0.688 true 2.563,0.896 2.875,1.094 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front No. 1 differential case sub-assembly.


c.
C117490

Remove the 16 bolts.


d.

Using a plastic-faced hammer, remove the front No. 1 differential case sub-assembly from the front differential ring gear.


Hide 41301L 5.INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41342A 6.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C318871

Using a 5 mm pin punch and hammer, remove the front differential pinion shaft straight pin from the front No. 1 differential case sub-assembly.


Hide 41342F 7.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C318253

Remove the front No. 1 differential pinion shaft from the front No. 1 differential case sub-assembly.


Hide 8.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41331F 9.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Set SST as shown in the illustration and tighten it.

C318254C01
4.583,0.292 5.094,0.292 false 4.99,1.323 4.396,1.219 4.396,1.219 4.979,1.104 true 0.927,2.354 1.24,2.552 0.313,0.198 10 false *b 2.792,0.344 3.104,0.542 0.313,0.198 10 false *a 4.229,0.208 4.615,0.396 0.385,0.188 10 false SST 4.073,1.156 4.458,1.344 0.385,0.188 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, conical spring, front No. 1 differential side gear thrust washer and front No. 1 differential case sub-assembly.


HINT:
·

Tighten SST until there is a clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C318255C01
2.188,1.427 2.385,1.427 2.385,1.427 2.479,2.042 false 1.375,0.646 1.688,0.844 0.313,0.198 10 false *a 1.833,1.333 2.198,1.521 0.365,0.188 10 true SST
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front No. 1 differential case sub-assembly.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



c.
C318256C01
1.708,0.51 1.938,0.51 1.938,0.51 2.365,0.823 true 2.385,1.573 2.167,1.698 2.167,1.698 2.406,1.833 true 1.833,2.927 2.063,2.927 2.063,2.927 2.365,2.573 true 1.76,2.573 1.99,2.573 1.99,2.573 2.25,2.417 true 1.76,0.885 1.99,0.885 1.99,0.885 2.271,1 true 1.938,1.625 2.25,1.823 0.313,0.198 10 false *1 1.542,0.823 1.75,1.01 0.208,0.188 10 false *2 1.542,0.438 1.75,0.625 0.208,0.188 10 false *3 1.573,2.5 1.75,2.708 0.177,0.208 10 true *2 1.573,2.854 1.781,3.042 0.208,0.188 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front No. 1 differential case sub-assembly, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front No. 1 differential case sub-assembly.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and conical spring.