Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008756 EA64F MANUAL TRANSMISSION / TRANSAXLE _0048565 DIFFERENTIAL CASE A

EA64F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41331F 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C01
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.719 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

Gear Oil


Coat the front differential side gear, front No. 1 differential side gear thrust washer and conical spring with gear oil.


b.
C318256C01
1.708,0.51 1.938,0.51 1.938,0.51 2.365,0.823 true 2.385,1.573 2.167,1.698 2.167,1.698 2.406,1.833 true 1.833,2.927 2.063,2.927 2.063,2.927 2.365,2.573 true 1.76,2.573 1.99,2.573 1.99,2.573 2.25,2.417 true 1.76,0.885 1.99,0.885 1.99,0.885 2.271,1 true 1.938,1.625 2.25,1.823 0.313,0.198 10 false *1 1.542,0.823 1.75,1.01 0.208,0.188 10 false *2 1.542,0.438 1.75,0.625 0.208,0.188 10 false *3 1.573,2.5 1.75,2.708 0.177,0.208 10 true *2 1.573,2.854 1.781,3.042 0.208,0.188 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front No. 1 differential case sub-assembly.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer and conical spring.

·

Make sure that the conical spring is installed in the correct orientation.




c.

Set SST as shown in the illustration and tighten it.

SST
09528-52010  (09528-05010, 09953-05010)

C318254C01
4.583,0.292 5.094,0.292 false 4.99,1.323 4.396,1.219 4.396,1.219 4.979,1.104 true 0.927,2.354 1.24,2.552 0.313,0.198 10 false *b 2.792,0.344 3.104,0.542 0.313,0.198 10 false *a 4.229,0.208 4.615,0.396 0.385,0.188 10 false SST 4.073,1.156 4.458,1.344 0.385,0.188 10 false SST
*a Turn *b Hold


NOTICE:

Do not overtighten SST, as doing so will damage the front differential side gear, conical spring, front No. 1 differential side gear thrust washer and front No. 1 differential case sub-assembly.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




d.
C301356C01
0,0 0,0 false
V100135

Gear Oil


Coat the front differential pinion and front differential pinion thrust washer with gear oil.


e.
C318260C01
2.156,1.365 2.354,1.365 2.354,1.365 2.469,1.969 false 1.833,1.292 2.146,1.49 0.313,0.198 10 true SST 1.281,1.135 1.594,1.333 0.313,0.198 10 false *a
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front No. 1 differential case sub-assembly.


NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C318261C01
0,0 0,0 false
V100135

Gear Oil


Coat a front No. 1 differential pinion shaft with gear oil.


b.

Install the front No. 1 differential pinion shaft to the front No. 1 differential case sub-assembly so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front No. 1 differential case sub-assembly.


Hide 41301L 4.INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C318262

Using a 5 mm pin punch and hammer, install the front differential pinion shaft straight pin to the front No. 1 differential case sub-assembly.


b.
C318263

Using a chisel and hammer, stake the front No. 1 differential case sub-assembly.


Hide 41221 6.INSTALL FRONT DIFFERENTIAL RING GEAR

a.

Clean the contact surface of the front No. 1 differential case sub-assembly and front differential ring gear.


b.

Using a heater, heat the front differential ring gear to 90 to 100°C (194 to 212°F).


c.
C318251C01
1.938,0.604 2.479,0.927 2.479,0.927 1.802,0.688 true 2.563,0.896 2.875,1.094 0.313,0.198 10 false *a
*a Matchmark


While aligning the matchmarks, quickly install the front differential ring gear to the front No. 1 differential case sub-assembly with the 16 bolts.

Torque:
106 N*m (1081 kgf*cm, 78 ft.*lbf)


Hide 41311E 7.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C318264N01
0.74,1.583 1.292,1.583 false 0.958,1.583 0.958,2 0.958,2 1.292,2 false 0.375,1.51 0.833,1.708 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing to the front No. 1 differential case sub-assembly.

SST
09316-20011  09513-36040  

NOTICE:

Be sure to install the front differential case front tapered roller bearing so that there is no clearance between the bearing inner race and front No. 1 differential case sub-assembly.



Hide 41311F 8.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C287724N01
0.635,0.542 1.135,0.542 false 0.333,0.49 0.792,0.688 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing to the front No. 1 differential case sub-assembly.

SST
09554-22010  

NOTICE:

Be sure to install the front differential case rear tapered roller bearing so that there is no clearance between the bearing inner race and front No. 1 differential case sub-assembly.



Hide 43410M 9.INSTALL FRONT DIFFERENTIAL CASE OIL SEAL

a.

Coat the lip of a new front differential case oil seal with MP grease.


b.
C318265C01
2.406,0.375 2.906,0.469 2.906,0.469 2.521,0.802 true 1.542,0.635 1.854,0.833 0.313,0.198 10 false *a 2.969,0.406 3.281,0.604 0.313,0.198 10 false SST
*a 21.5 to 22.5 mm (0.847 to 0.885 in.)


Using SST and a hammer, tap in a new front differential case oil seal to the front differential case.

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Standard depth:

21.5 to 22.5 mm (0.847 to 0.885 in.)


NOTICE:

Do not damage the front differential case oil seal lip.