Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049182 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  DISASSEMBLY  


PROCEDURE

Hide 41221 2.REMOVE FRONT DIFFERENTIAL RING GEAR

a.
C317727C03
1.167,1.469 0.427,0.99 0.427,0.99 1.229,1.406 true 0.24,0.833 0.677,1.25 0.438,0.417 10 false *a
*a Matchmark


Put matchmarks on the front differential ring gear and front differential case.


b.
C317728

Remove the 12 bolts from the front differential ring gear.


c.
C317729

Using a plastic-faced hammer, tap on the front differential ring gear to remove it from the front differential case.


Hide 41342A 3.REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C317730

Using a 5 mm pin punch and a hammer, remove the front differential pinion shaft straight pin from the front differential case.

NOTICE:

Before removing the front differential pinion shaft straight pin, unstake it with a pin punch.



Hide 41342F 4.REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C138706

Remove the front No. 1 differential pinion shaft from the front differential case.


Hide 5.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 6.REMOVE FRONT DIFFERENTIAL SIDE GEAR

a.

Install SST as shown in the illustration and tighten it.

C288037C04
4.906,1.75 4.292,0.979 4.292,0.979 4.906,1.469 true 4.573,0.385 4.948,0.385 true 3.052,0.438 3.365,0.594 0.313,0.156 10 false *a 0.885,2.229 1.198,2.385 0.313,0.156 10 false *b 3.99,0.896 4.448,1.094 0.458,0.198 10 false SST 4.292,0.313 4.75,0.51 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST, as doing so will damage the 2 front differential side gears, 2 conical spring washers, 2 front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST until there is clearance between the front differential pinions and front differential side gears.

·

When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.




b.
C288039C03
2.396,1.823 2.521,1.823 2.521,1.823 2.802,1.26 true 2.094,1.75 2.552,1.948 0.458,0.198 10 false SST 1.708,0.229 2.021,0.427 0.313,0.198 10 false *a
*a Turn


Install SST as shown in the illustration, rotate the front differential side gear, and then remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.

SST
09528-52010  (09528-05030)

NOTICE:

Do not drop the front differential pinion and front differential pinion thrust washer.



c.
C288038C04
2.542,1.167 2.25,1 2.25,1 2.542,0.865 true 1.917,0.177 2.313,0.177 true 1.917,0.333 2.313,0.333 true 1.917,1.708 2.313,1.708 true 1.917,1.865 2.313,1.865 true 2.063,0.927 2.375,1.083 0.313,0.156 10 false *1 1.76,0.25 2.073,0.406 0.313,0.156 10 false *2 1.76,0.094 2.073,0.25 0.313,0.156 10 false *3 1.74,1.615 2.052,1.771 0.313,0.156 10 false *2 1.75,1.792 2.063,1.948 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer


Remove SST from the front differential case, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical spring washers from the front differential case.

NOTICE:

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring washer.