Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › from 2014.10
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0049182 DIFFERENTIAL CASE A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C288461C05
0.771,0.688 0.635,0.302 0.635,0.302 0.552,0.302 false 1.719,0.74 1.583,0.333 1.583,0.333 1.5,0.333 false 2.5,0.708 2.365,0.323 2.365,0.323 2.281,0.323 false 0.406,0.229 0.719,0.385 0.313,0.156 10 false *1 1.323,0.25 1.635,0.406 0.313,0.156 10 false *2 2.104,0.25 2.417,0.406 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer
V100135

Toyota Genuine ATF WS


Coat the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical spring washers with ATF.


b.
C288038C04
2.542,1.167 2.25,1 2.25,1 2.542,0.865 true 1.917,0.177 2.313,0.177 true 1.917,0.333 2.313,0.333 true 1.917,1.708 2.313,1.708 true 1.917,1.865 2.313,1.865 true 2.063,0.927 2.375,1.083 0.313,0.156 10 false *1 1.76,0.25 2.073,0.406 0.313,0.156 10 false *2 1.76,0.094 2.073,0.25 0.313,0.156 10 false *3 1.74,1.615 2.052,1.771 0.313,0.156 10 false *2 1.75,1.792 2.063,1.948 0.313,0.156 10 false *3
*1 Front Differential Side Gear
*2 Conical Spring Washer
*3 Front No. 1 Differential Side Gear Thrust Washer


Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical spring washers to the front differential case.

NOTICE:
·

Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring washer.

·

Make sure that the conical spring washer is installed with the correct orientation.




c.

Install SST as shown in the illustration and tighten it.

C288037C04
4.906,1.75 4.292,0.979 4.292,0.979 4.906,1.469 true 4.573,0.385 4.948,0.385 true 3.052,0.438 3.365,0.594 0.313,0.156 10 false *a 0.885,2.229 1.198,2.385 0.313,0.156 10 false *b 3.99,0.896 4.448,1.094 0.458,0.198 10 false SST 4.292,0.313 4.75,0.51 0.458,0.198 10 false SST
*a Turn *b Hold


SST
09528-52010  (09528-05010, 09953-05010)

NOTICE:

Do not overtighten SST as doing so will damage the front differential side gears, conical spring washers, front No. 1 differential side gear thrust washers and front differential case.


HINT:
·

Tighten SST to create the necessary clearance to install the front differential pinions.

·

When installing the 2 front differential pinions, do not overtighten SST, as it is necessary to rotate the 2 front differential side gears.




d.
C287727C04
0,0 0,0 false
V100135

Toyota Genuine ATF WS


Coat the 2 front differential pinions and 2 front differential pinion thrust washers with ATF.


e.
C288040C02
2.385,1.823 2.563,1.823 2.563,1.823 2.802,1.25 true 1.531,0.573 1.844,0.771 0.313,0.198 10 false *a 2.073,1.76 2.385,1.958 0.313,0.198 10 false SST
*a Turn


Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions to 2 front differential pinion thrust washers.

SST
09528-52010  (09528-05030)

CAUTION:

Be careful not to catch your fingers between the front differential pinion and front differential case.


NOTICE:

Do not drop the front differential pinion or front differential pinion thrust washer.



Hide 2.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C291659C02
0,0 0,0 false
V100135

Toyota Genuine ATF WS


Coat the front No. 1 differential pinion shaft with ATF.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C200237

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C310023

Using a chisel and a hammer, stake the front differential case.


Hide 41221 6.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
D025215

Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

NOTICE:

Do not heat the front differential ring gear to more than 110°C (230°F).



b.
C317727C04
1.167,1.469 0.427,0.99 0.427,0.99 1.229,1.406 true 0.24,0.833 0.677,1.25 0.438,0.417 10 false *a
*a Matchmark


Clean the contact surface of the front differential case.


c.

Align the matchmarks, and install the front differential ring gear to the front differential case quickly.


d.
C317728

Install the 12 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.

·

Tighten the bolts evenly in a diagonal pattern using several steps.