Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2014.10–2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

This circuit sends a microphone signal from the telephone microphone assembly to the radio and display receiver assembly.

It also supplies power from the radio and display receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E291289E03
0.844,0.656 1.583,1.198 0.74,0.542 10 false Telephone Microphone Assembly 0.552,2.51 1.292,3.052 0.74,0.542 10 false Q7 0.542,2.667 1.917,2.844 1.375,0.177 10 false Map Light Assembly 0.229,3.323 1.604,3.5 1.375,0.177 10 false *: Shielded 3.365,1.896 3.5,2.052 0.135,0.156 10 false * 4.604,1.906 4.74,2.063 0.135,0.156 10 false * 1.792,0.448 2.406,0.656 0.615,0.208 10 false MACC 1.792,0.833 2.49,1.031 0.698,0.198 10 false MCO+ 1.813,1.219 2.427,1.417 0.615,0.198 10 false MCO- 1.833,2 2.292,2.198 0.458,0.198 10 false SNS2 2.313,0.427 2.927,0.635 0.615,0.208 10 false 11 2.302,0.844 2.917,1.052 0.615,0.208 10 false 10 2.323,1.24 2.938,1.448 0.615,0.208 10 false 9 2.344,2.01 2.958,2.219 0.615,0.208 10 false 12 5.698,0.531 6.313,0.74 0.615,0.208 10 false MACC 5.708,0.948 6.104,1.146 0.396,0.198 10 false MIN+ 5.698,1.333 6.094,1.531 0.396,0.198 10 false MIN- 5.688,1.729 6.417,1.927 0.729,0.198 10 false SGND 5.698,2.135 6.094,2.333 0.396,0.198 10 false SNS2 5.458,2.01 6.073,2.219 0.615,0.208 10 false 6 5.406,1.594 6.021,1.802 0.615,0.208 10 false 18 5.406,1.198 6.021,1.406 0.615,0.208 10 false 19 5.479,0.844 6.094,1.052 0.615,0.208 10 false 5 5.479,0.417 6.094,0.625 0.615,0.208 10 false 4 5.188,2.479 5.802,2.688 0.615,0.208 10 false G143 5.188,2.646 6.906,2.99 1.719,0.344 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E280108C12
0.198,0.917 0.583,1.125 0.385,0.208 2.021,1.323 1.25,1.813 1.25,1.813 1.01,1.813 true 2.167,1.333 2.25,1.896 2.25,1.896 2.406,1.896 true 2.156,1.083 2.292,0.292 2.292,0.292 2.448,0.292 true 0,0 0.313,0.156 0.313,0.156 10 false *a 0.229,0.938 0.688,1.125 0.458,0.188 10 false G143 0.604,1.719 0.958,1.917 0.354,0.198 10 false MIN- 2.469,1.802 3.135,1.979 0.667,0.177 10 false SGND 2.542,0.198 3.031,0.365 0.49,0.167 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-19 (MIN-) - Body ground Always Below 1 Ω
G143-18 (SGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the Q7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-4 (MACC) - Q7-11 (MACC) Always Below 1 Ω
G143-5 (MIN+) - Q7-10 (MCO+) Always Below 1 Ω
G143-19 (MIN-) - Q7-9 (MCO-) Always Below 1 Ω
G143-6 (SNS2) - Q7-12 (SNS2) Always Below 1 Ω
G143-4 (MACC) - Body ground Always 10 kΩ or higher
G143-5 (MIN+) - Body ground Always 10 kΩ or higher
G143-19 (MIN-) - Body ground Always 10 kΩ or higher
G143-18 (SGND) - Body ground Always 10 kΩ or higher
G143-6 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER MICROPHONE ASSEMBLY>REMOVAL


b.

Check if the same problem occurs again.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAP LIGHT ASSEMBLY