Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2014.10–2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Microphone Circuit between Radio Receiver and Extension Module  


DESCRIPTION

This circuit sends a microphone voice signal from the navigation ECU to the radio and display receiver assembly.

Using this circuit, the navigation ECU disables the microphone function of the radio and display receiver assembly to receive a microphone voice signal from the telephone microphone assembly.

WIRING DIAGRAM

E292629E02
1.375,0.365 1.823,0.51 0.448,0.146 10 false MIC+ 1.365,0.854 1.813,1 0.448,0.146 10 false MIC- 1.365,1.313 1.813,1.458 0.448,0.146 10 false SLD4 1.896,0.26 2.344,0.406 0.448,0.146 10 false 5 1.885,0.74 2.333,0.885 0.448,0.146 10 false 6 1.906,1.229 2.354,1.375 0.448,0.146 10 false 1 0.885,1.708 1.323,1.917 0.438,0.208 10 false Y1 0.865,1.875 2.083,2.26 1.219,0.385 10 false Radio and Display Receiver Assembly 3.052,1.875 4.521,2.073 1.469,0.198 10 false No. 1 Navigation Wire 5.406,0.271 5.698,0.417 0.292,0.146 10 false 16 5.417,0.75 5.708,0.896 0.292,0.146 10 false 17 5.427,1.229 5.719,1.375 0.292,0.146 10 false 18 5.729,0.344 6.177,0.49 0.448,0.146 10 false MIC+ 5.74,0.854 6.188,1 0.448,0.146 10 false MIC- 5.708,1.323 6.365,1.469 0.656,0.146 10 false MSHLD 5.563,1.74 6.219,1.885 0.656,0.146 10 false Y5 5.542,1.875 6.719,2.052 1.177,0.177 10 false Navigation ECU

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK NO. 1 NAVIGATION WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the Y1 radio and display receiver assembly connector.


b.

Disconnect the Y5 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-5 (MIC+) - Y5-16 (MIC+) Always Below 1 Ω
Y1-6 (MIC-) - Y5-17 (MIC-) Always Below 1 Ω
Y1-1 (SLD4) - Y5-18 (MSHLD) Always Below 1 Ω
Y1-5 (MIC+) - Body ground Always 10 kΩ or higher
Y1-6 (MIC-) - Body ground Always 10 kΩ or higher
Y1-1 (SLD4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG