Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › from 2014.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066373 OCCUPANT CLASSIFICATION SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then displays the front passenger airbag condition (activated/not activated) using the passenger airbag ON/OFF indicator.

HINT:

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.


Front Passenger Seat Condition Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
Vacant Off On Off
Adult is seated. On Off Off
Child is seated. Off On Off
Child restraint system is installed.
Occupant classification system failure Off On On

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch to ON, and check the SRS warning light condition.

HINT:

If passenger airbag ON/OFF indicator trouble occurs, the SRS warning light does not illuminate. If the light comes on, a DTC is stored. Troubleshoot for the DTC.


OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

2.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK

NG

2.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform zero point calibration and sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration & Sensitivity Check
50005 59 4206
OK:

"Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.



Result:
Proceed to
OK
NG



OK

END

NG

3.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
3.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
a.

Loosen the 4 installation bolts of the front seat assembly RH.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION


b.

Tighten the 4 installation bolts of the front seat assembly RH to the specified torque.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION


Result:
Proceed to
NEXT



NEXT

4.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
4.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform zero point calibration and sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration & Sensitivity Check
50005 59 4206
OK:

"Zero Point Calibration is complete." and "Sensitivity Check is complete." are displayed.



Result:
Proceed to
OK
NG



OK

END

NG

5.READ VALUE USING GTS
5.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST

i.

Read the display when the passenger side buckle switch is operated.

Body Electrical > Occupant Detection > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Passenger Buckle SW Front seat belt assembly RH buckle switch Set, Unset or NG Set: The front seat belt assembly RH is fastened
Unset: The front seat belt assembly RH is not fastened
NG: Data is not determined
-
Body Electrical > Occupant Detection > Data List
Tester Display
Passenger Buckle SW
50003 59 21
OK:

The GTS display changes correctly in accordance with the operation of the buckle switch.




Result:
Result
OK
NG



OK

6.CHECK CONNECTORS

NG

9.CHECK CONNECTORS
6.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the connectors from the occupant detection ECU, front and rear occupant classification sensor LH.


d.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Result
OK
NG



OK

7.REPLACE OCCUPANT DETECTION ECU

NG

REPLACE FRONT SEAT WIRE RH

7.REPLACE OCCUPANT DETECTION ECU
a.

Connect the connectors to the front and rear occupant classification sensor LH.



c.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
NEXT



NEXT

8.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
8.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform zero point calibration and sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration & Sensitivity Check
50005 59 4206

Result:
Proceed to
NEXT



NEXT

END

9.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


d.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Result
OK
NG



OK

10.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPLACE FRONT SEAT WIRE RH

10.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Connect the connector to the occupant detection ECU.


b.

Replace the front seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


c.

Connect the cable to the negative (-) battery terminal.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
11.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK
a.

Using the GTS, perform zero point calibration and sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration & Sensitivity Check
50005 59 4206

Result:
Proceed to
NEXT



NEXT

END