Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) C

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  P0617  Starter Relay Circuit High  


DESCRIPTION

When the engine is started by stop and start control, the engine stop and start ECU controls the starter assembly by activating the ST NO. 1 relay (for starter pinion operation) via voltage from terminal STA and then, using its built-in starter delay circuit, activating the ST NO. 2 relay (for starter motor operation) via voltage from terminal STA2.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P0617 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0617 Starter Relay Circuit High Both of the following conditions are met for 1 second (1 trip detection logic):
·

Ignition switch ON

·

Overcurrent to ST NO. 1 relay or ST NO. 2 relay is detected.


·

Wire harness or connector

·

ST NO. 1 relay

·

ST NO. 2 relay

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



WIRING DIAGRAM

A350407E01
0.083,0.073 2.354,0.365 2.271,0.292 12 false w/o Entry and Start System: 0.417,0.958 0.875,1.156 0.458,0.198 10 false BBC 0.125,0.76 0.281,0.958 0.156,0.198 10 false 2 0.104,1.115 0.26,1.313 0.156,0.198 10 false 1 5.135,0.635 5.594,0.833 0.458,0.198 10 false A65 5.24,0.448 5.396,0.646 0.156,0.198 10 false 7 5.135,1.115 5.594,1.313 0.458,0.198 10 false A66 5.177,0.917 5.49,1.115 0.313,0.198 10 false 21 5.49,0.635 5.948,0.833 0.458,0.198 10 false BIN 5.5,1.115 5.958,1.313 0.458,0.198 10 false STA 5.51,1.573 5.969,1.771 0.458,0.198 10 false STA2 5.51,2.01 5.969,2.208 0.458,0.198 10 false CLL 5.146,1.573 5.604,1.771 0.458,0.198 10 false A66 5.177,1.375 5.49,1.573 0.313,0.198 10 false 23 5.146,2.01 5.604,2.208 0.458,0.198 10 false A66 5.188,1.813 5.5,2.01 0.313,0.198 10 false 28 4.823,2.427 6.583,2.656 1.76,0.229 10 false Engine Stop and Start ECU 5.802,1.323 6.417,1.521 0.615,0.198 10 false CANH 5.802,1.802 6.417,2 0.615,0.198 10 false CANL 6.281,1.323 6.74,1.521 0.458,0.198 10 false G87 6.313,1.125 6.625,1.323 0.313,0.198 10 false 15 5.885,0.615 6.344,0.813 0.458,0.198 10 false GND 6.281,0.615 6.74,0.813 0.458,0.198 10 false A65 6.354,0.427 6.51,0.625 0.156,0.198 10 false 8 6.281,1.813 6.74,2.01 0.458,0.198 10 false G87 6.313,1.594 6.625,1.792 0.313,0.198 10 false 16 5.615,5.25 6.073,5.448 0.458,0.198 10 false ECM 5.615,5.073 6.073,5.271 0.458,0.198 10 false A62 5.823,3.865 6.438,4.063 0.615,0.198 10 false CANL 6.281,3.688 6.594,3.885 0.313,0.198 10 false 26 6.292,4.385 6.604,4.583 0.313,0.198 10 false 13 5.802,4.583 6.417,4.781 0.615,0.198 10 false CANH 5.49,3.99 5.948,4.188 0.458,0.198 10 false NSW 5.5,4.344 5.958,4.542 0.458,0.198 10 false STA 5.219,4.229 5.531,4.427 0.313,0.198 10 false 29 5.208,3.865 5.521,4.063 0.313,0.198 10 false 23 1.479,3.802 3.771,4.031 2.292,0.229 10 false Ignition or Starter Switch Assembly 1.469,3.615 1.781,3.813 0.313,0.198 10 false G4 2.625,3.188 3.083,3.385 0.458,0.198 10 false ST2 1.792,3.188 2.25,3.385 0.458,0.198 10 false AM2 1.583,3.177 1.74,3.375 0.156,0.198 10 false 4 2.979,3.177 3.135,3.375 0.156,0.198 10 false 2 1.115,3.427 1.573,3.625 0.458,0.198 10 false AM2 2.333,1.646 3.656,2.302 1.323,0.656 10 false Park/Neutral Position Switch Assembly 2.323,1.406 2.781,1.604 0.458,0.198 10 false B36 1.635,1.417 1.792,1.615 0.156,0.198 10 false 9 1.906,2.375 2.063,2.573 0.156,0.198 10 false 4 4.458,5.438 5.25,5.656 0.792,0.219 10 false ST NO. 2 4.271,5 4.427,5.198 0.156,0.198 10 false 2 4.271,5.76 4.427,5.958 0.156,0.198 10 false 1 3.677,5.01 3.833,5.208 0.156,0.198 10 false 5 3.677,5.76 3.833,5.958 0.156,0.198 10 false 3 2.625,4.51 3.417,4.729 0.792,0.219 10 false ST NO. 2 1.198,4.771 1.99,4.99 0.792,0.219 10 false ST NO. 1 2.292,5.521 3.083,5.74 0.792,0.219 10 false ST NO. 1 2.156,5.156 2.313,5.354 0.156,0.198 10 false 5 2.167,5.917 2.323,6.115 0.156,0.198 10 false 3 1.542,5.906 1.698,6.104 0.156,0.198 10 false 1 1.531,5.167 1.688,5.365 0.156,0.198 10 false 2 0.479,7.75 1.552,7.948 1.073,0.198 10 false Battery 0.406,5.781 1.479,5.979 1.073,0.198 10 false FL MAIN 1.865,7.594 4.313,7.792 2.448,0.198 10 false Starter Assembly 1.156,7.167 1.615,7.365 0.458,0.198 10 false B96 1.229,6.927 1.385,7.125 0.156,0.198 10 false 1 1.948,6.885 2.406,7.083 0.458,0.198 10 false B87 2.302,6.875 2.458,7.073 0.156,0.198 10 false 2 1.521,7.167 1.677,7.365 0.156,0.198 10 false B 1.948,7.104 2.406,7.302 0.458,0.198 10 false SL1 3,7.229 3.458,7.427 0.458,0.198 10 false SL2 3.406,7.24 3.865,7.438 0.458,0.198 10 false B87 3.469,7.021 3.625,7.219 0.156,0.198 10 false 1 0.854,8.396 4.521,8.594 3.667,0.198 10 false : CAN Communication Line

A350408E01
0.063,0.052 4.042,0.323 3.979,0.271 12 false w/ Entry and Start System: 5.167,0.969 5.625,1.167 0.458,0.198 10 false A66 5.208,0.771 5.521,0.969 0.313,0.198 10 false 21 5.521,0.969 5.979,1.167 0.458,0.198 10 false STA 5.167,1.344 5.625,1.542 0.458,0.198 10 false A65 5.521,1.323 5.979,1.521 0.458,0.198 10 false BIN 5.25,1.167 5.406,1.365 0.156,0.198 10 false 7 5.531,1.719 5.99,1.917 0.458,0.198 10 false STA2 5.177,1.719 5.635,1.917 0.458,0.198 10 false A66 5.208,1.531 5.521,1.729 0.313,0.198 10 false 23 5.156,2.177 5.615,2.375 0.458,0.198 10 false A66 5.219,1.99 5.531,2.188 0.313,0.198 10 false 28 5.833,1.469 6.448,1.667 0.615,0.198 10 false CANH 6.313,1.479 6.771,1.677 0.458,0.198 10 false G87 6.344,1.281 6.656,1.479 0.313,0.198 10 false 15 6.313,1.958 6.771,2.156 0.458,0.198 10 false G87 5.833,1.958 6.448,2.156 0.615,0.198 10 false CANL 5.521,2.177 5.979,2.375 0.458,0.198 10 false CLL 5.917,0.792 6.375,0.99 0.458,0.198 10 false GND 6.323,0.792 6.781,0.99 0.458,0.198 10 false A65 6.406,0.583 6.719,0.781 0.313,0.198 10 false 8 6.354,1.76 6.667,1.958 0.313,0.198 10 false 16 4.927,2.552 6.656,2.771 1.729,0.219 10 false Engine Stop and Start ECU 0.177,2.563 1.26,3.115 1.083,0.552 10 false Certification ECU (Smart Key ECU Assembly) 1.094,0.979 1.552,1.177 0.458,0.198 10 false G82 1.188,0.771 1.344,0.969 0.156,0.198 10 false 7 0.698,0.979 1.156,1.177 0.458,0.198 10 false STA 0.625,2.063 1.083,2.26 0.458,0.198 10 false STAR 1.083,2.063 1.542,2.26 0.458,0.198 10 false G82 2.344,2.906 2.5,3.104 0.156,0.198 10 false 4 2.708,2.198 4.031,2.896 1.323,0.698 10 false Park/Neutral Position Switch Assembly 2.708,1.99 3.167,2.188 0.458,0.198 10 false B36 2.073,1.875 2.229,2.073 0.156,0.198 10 false 9 5.844,4.635 6.458,4.833 0.615,0.198 10 false CANL 5.823,5.385 6.438,5.583 0.615,0.198 10 false CANH 6.313,5.198 6.625,5.396 0.313,0.198 10 false 13 6.313,4.479 6.625,4.677 0.313,0.198 10 false 26 5.51,4.854 5.969,5.052 0.458,0.198 10 false NSW 5.26,4.729 5.573,4.927 0.313,0.198 10 false 23 5.51,5.156 5.969,5.354 0.458,0.198 10 false STA 5.26,5.052 5.573,5.25 0.313,0.198 10 false 29 5.531,5.844 5.99,6.042 0.458,0.198 10 false A62 5.531,6.021 5.99,6.219 0.458,0.198 10 false ECM 0.844,4.01 1.302,4.208 0.458,0.198 10 false BBC 1.156,1.844 1.313,2.042 0.156,0.198 10 false 5 1.177,3.698 1.333,3.896 0.156,0.198 10 false 2 0.698,3.688 0.854,3.885 0.156,0.198 10 false 1 2.708,4.458 3.396,4.656 0.688,0.198 10 false ST NO. 2 4.76,6.76 5.448,6.958 0.688,0.198 10 false ST NO. 2 4.604,6.385 4.76,6.583 0.156,0.198 10 false 2 4.594,7.146 4.75,7.344 0.156,0.198 10 false 1 4.01,6.396 4.167,6.594 0.156,0.198 10 false 5 4.031,7.156 4.188,7.354 0.156,0.198 10 false 3 2.146,5.313 2.302,5.51 0.156,0.198 10 false 5 2.156,6.073 2.313,6.271 0.156,0.198 10 false 3 1.531,5.323 1.688,5.521 0.156,0.198 10 false 2 1.521,6.073 1.677,6.271 0.156,0.198 10 false 1 2.323,5.656 3.01,5.854 0.688,0.198 10 false ST NO. 1 0.76,4.958 1.448,5.156 0.688,0.198 10 false ST NO. 1 0.427,5.938 1.5,6.135 1.073,0.198 10 false FL MAIN 0.479,7.719 1.552,7.917 1.073,0.198 10 false Battery 1.521,7.635 2.896,7.833 1.375,0.198 10 false Starter Assembly 0.854,8.458 4.521,8.656 3.667,0.198 10 false : CAN Communication Line 0.833,7.063 1.292,7.26 0.458,0.198 10 false B96 0.906,6.823 1.063,7.021 0.156,0.198 10 false 1 1.188,7.052 1.344,7.25 0.156,0.198 10 false B 1.948,6.76 2.406,6.958 0.458,0.198 10 false B87 2.302,6.75 2.458,6.948 0.156,0.198 10 false 2 1.938,6.99 2.396,7.188 0.458,0.198 10 false SL1 2.688,7.354 3.146,7.552 0.458,0.198 10 false SL2 3.073,7.354 3.531,7.552 0.458,0.198 10 false B87 3.146,7.135 3.302,7.333 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC FUSE)
a.

Disconnect the A65 engine stop and start ECU connector.


b.

Remove the BBC fuse from engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-7 (BIN) - BBC fuse terminal 2 Always Below 1 Ω
A65-7 (BIN) - Body ground Always 10 kΩ or higher
BBC fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1, ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST NO. 1, ST NO. 2 RELAY)
a.

Disconnect the A66 and A65 engine stop and start ECU connectors.


b.

Remove the ST NO. 1 and ST NO. 2 relay from No. 2 engine room relay block and junction block assembly.


c.

Remove the BBC fuse from engine room relay block and junction block assembly.


d.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the B36 park/neutral position switch assembly connector.


f.

Disconnect the A62 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST NO. 1 relay terminal 2 Always Below 1 Ω
A66-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST NO. 1 relay terminal 2 - Body ground Always 10 kΩ or higher
A66-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher
A65-7 (BIN) - A66-21 (STA) Always 10 kΩ or higher
A65-7 (BIN) - A66-23 (STA2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
a.

Disconnect the engine stop and start ECU connectors.

A348145C01
0.594,2.125 1.115,2.344 0.521,0.219 1.458,0.198 1.979,0.417 0.521,0.219 2.594,2.115 3.115,2.333 0.521,0.219 5.344,2.115 5.865,2.333 0.521,0.219 3.104,0.198 3.625,0.417 0.521,0.219 4.958,0.198 5.479,0.417 0.521,0.219 0.719,2.156 1.031,2.333 0.313,0.177 10 false A65 1.594,0.229 1.906,0.406 0.313,0.177 10 false A65 2.729,2.156 3.188,2.354 0.458,0.198 10 false A66 3.24,0.24 3.698,0.438 0.458,0.198 10 false A66 5.094,0.229 5.552,0.427 0.458,0.198 10 false G87 5.479,2.146 5.938,2.344 0.458,0.198 10 false G87 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - A65-8 (GND) Always 10 kΩ or higher
A66-23 (STA2) - A65-8 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)

NG

4.INSPECT RELAY (ST NO. 1, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

NG

REPLACE RELAY (ST NO. 1, ST NO. 2 RELAY)