The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.
If the output value of the vacuum sensor assembly remains the same even though the brake booster assembly pressure changes when the brake pedal is operated or the vehicle is being driven, the engine stop and start ECU judges that the sensor is stuck.
When sticking of the sensor is detected, the engine stop and start ECU stores DTC P1541 and blinks the stop and start cancel indicator light.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P1541 | Brake Booster Sensor Circuit | Any of the following conditions are met (1 trip detection logic):
·
The change in vacuum is 0.3 kPa or less more than 3 times when the brake pedal is firmly depressed to stop the vehicle (deceleration of 0.15 G or more for 1 second or more). ·
The change in vacuum while stopping the vehicle 30 times from a speed of 30 km/h (19 mph) or more was 0.3 kPa or less |
·
Vacuum sensor assembly ·
Brake booster assembly ·
Check valve to connector tube hose (Brake booster hose) ·
Engine stop and start ECU |
Blinks | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
Start the engine and warm it up.
Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.
| Tester Display |
|---|
| Brake Boost Pressure |
Drive the vehicle at 30 km/h (19 mph) or more and stop the vehicle. Repeat this driving pattern 30 times to allow the brake booster vacuum to change.
Stop the vehicle.
Check that DTCs are not output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Allow the engine to stop by stop and start control. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>REGISTRATION
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 3ZR-FAE)>FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Read any other DTCs.
| Result | Proceed to |
|---|---|
| DTC P1541 is output | A |
| DTC P1541 and other DTCs output | B |
A
B
Start the engine and warm it up.
Turn the ignition switch off. (*1)
Turn the ignition switch to ON. (engine is stopped) (*2)
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure. (*3)
| Tester Display |
|---|
| Brake Boost Pressure |
Depress the brake pedal 5 times and read the changes in the following pressure value.
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Brake Boost Pressure | ·
Ignition switch ON ·
Brake pedal depressed 5 times |
Changes by 20 kPa (150 mmHg, 5.91 in. Hg) or higher |
Because it is hard to cause variation in the internal pressure before and after depressing the brake pedal if the brake booster internal pressure is high before depressing the brake pedal, do not operate the brake pedal as much as possible between operations (*1) and (*3).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the check valve to connector tube hose (brake booster hose) for cracks or clogging (visual check).
If the braking force is abnormal, inspect the brake booster assembly.
No cracks or clogging in the check valve to connector tube hose (brake booster hose).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the vacuum sensor assembly.
Click hereEngine / Hybrid System>STOP AND START>VACUUM SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Clear the DTC.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.
| Tester Display |
|---|
| Brake Boost Pressure |
Drive the vehicle at 30 km/h (19 mph) or more and stop the vehicle. Repeat this driving pattern 30 times to allow the brake booster vacuum to change.
Stop the vehicle.
Check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P1541 is output | B |
A
B