Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 3ZR-FAE) › 2015.04–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0166176 STOP AND START SYSTEM(for 3ZR-FAE) J

STOP AND START  STOP AND START SYSTEM(for 3ZR-FAE)  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine stop and start ECU detects whether the engine hood is open or closed based on a signal received from the engine hood courtesy switch built into the hood lock assembly.

·

The engine stop and start ECU prohibits starting of the engine by stop and start control and changes the mode to "stalled" if the engine hood is opened with the shift lever in D or M while the engine is stopped by stop and start control.


WIRING DIAGRAM

A287084E32
3.458,0.896 4.031,1.115 0.573,0.219 10 false 1 1.896,0.906 2.563,1.177 0.667,0.271 10 false 2 1.76,1.531 2.521,1.823 0.76,0.292 10 false A50 1.76,1.677 3.646,2.135 1.885,0.458 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.354,1.823 5.875,2 0.521,0.177 10 false A66 5.406,0.938 5.792,1.125 0.385,0.188 10 false 7 5.604,1.052 6.281,1.365 0.677,0.313 10 false BNT1 5.344,1.99 7.083,2.292 1.74,0.302 10 false Engine Stop and Start ECU 3.167,1.031 3.323,1.229 0.156,0.198 10 false + 2.156,1.031 2.313,1.229 0.156,0.198 10 false E

PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SWITCH)
NOTICE:

Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.


e.

According to the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Hood Courtesy Switch
50003 227 8
OK:
Tester Display Condition Normal Condition
Hood Courtesy Switch Engine hood closed ON
Engine hood open OFF



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
a.

Remove the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL


b.

Inspect the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the A50 engine hood courtesy switch (hood lock assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A50 engine hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-7 (BNT1) - A50-1 (+) Always Below 1 Ω
A66-7 (BNT1) - Body ground Always 10 kΩ or higher
A50-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR