Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2015.04–2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0717  Input / Turbine Speed Sensor "A" Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

The ECM receives a signal from the transmission revolution sensor (NT) installed in the continuously variable transaxle to control the lock-up engagement pressure and forward and reverse clutch pressure.

The transmission revolution sensor (NT) detects the continuously variable transaxle input shaft speed and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Input / Turbine Speed Sensor "A" Circuit No Signal 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more, and no error is detected in the park/neutral position switch assembly.

2.

The speed indicated by the transmission revolution sensor (NT) is less than 300 rpm.

3.

2 seconds

4.

1-trip detection logic


·

Harness or connector

·

Transmission revolution sensor (NT)

·

ECM


Comes on DTC stored
P07BF Input/Turbine Speed Sensor "A" Circuit Low 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

A transmission revolution sensor (NT) signal malfunction is not detected.

2.

The transmission revolution sensor (NT) output voltage is below 0.1 V.

3.

2 seconds

4.

1-trip detection logic


·

Harness or connector

·

Transmission revolution sensor (NT)

·

ECM


Comes on DTC stored
P07C0 Input/Turbine Speed Sensor "A" Circuit High 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

A transmission revolution sensor (NT) signal malfunction is not detected.

2.

The transmission revolution sensor (NT) output voltage is higher than 1.9 V.

3.

2 seconds

4.

1-trip detection logic


·

Harness or connector

·

Transmission revolution sensor (NT)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The transmission revolution sensor (NT) detects the transaxle input shaft speed. The ECM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input shaft speed) with the transmission revolution sensor (NOUT) (output shaft speed).

When the output shaft speed is higher than the expected value and the input shaft speed is less than 300 rpm while driving with the shift lever in D, the ECM will determine that the transmission revolution sensor (NT) is malfunctioning. The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C298189E08
0.094,2.896 2.771,3.146 2.677,0.25 10 false Transmission Revolution Sensor (NT) 0.104,2.729 0.563,2.927 0.458,0.198 10 false B33 1.708,1.135 2.323,1.333 0.615,0.198 10 false NTB 5.688,1.25 6.302,1.448 0.615,0.198 10 false NTB 5.688,2.219 6.302,2.417 0.615,0.198 10 false NTO 1.688,2.104 2.302,2.302 0.615,0.198 10 false NTO 5.917,2.948 6.531,3.146 0.615,0.198 10 false B93 5.906,3.135 6.521,3.333 0.615,0.198 10 false ECM 5.333,1.135 5.792,1.333 0.458,0.198 10 false 126 5.333,2.104 5.792,2.302 0.458,0.198 10 false 125 2.094,1.135 2.552,1.333 0.458,0.198 10 false 2 2.094,2.104 2.552,2.302 0.458,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

·

0 rpm: Vehicle stopped with shift lever in R


Data is displayed in increments of 50 rpm.
NT Sensor Voltage Input turbine speed (NT) sensor output voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N) -
Powertrain > Engine and ECT > Data List
Tester Display
SPD (NT)
NT Sensor Voltage
50003 234 390,391

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

B

5.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.

Remove the transmission revolution sensor (NT).

Click hereDrivetrain>K114F MULTIDRIVE / CVT>REVOLUTION SENSOR>REMOVAL


b.

Connect the battery to the sensor as shown in the illustration.

C277851C12
1.333,1.958 1.594,1.469 true 4.521,1.156 4.229,0.979 true 3.667,1.146 3.948,0.969 true 2.063,1.948 1.802,1.469 true 6.115,1.24 5.813,1.01 true 4.906,0.844 4.813,0.552 true 4.698,2.563 4.927,2.302 false 6.135,1.677 5.448,2.146 true 4.969,0.781 5.281,0.938 0.313,0.156 10 false *2 6.198,1.188 6.51,1.385 0.313,0.198 10 false *1 1,0.563 1.313,0.719 0.313,0.156 10 false *a 4.49,2.479 4.802,2.635 0.313,0.156 10 false *c 1.135,2.01 1.583,2.219 0.448,0.208 10 false NTB 1.979,2.01 2.438,2.219 0.458,0.208 10 false NTO 4.583,1.094 4.771,1.292 0.188,0.198 10 false 1 3.552,1.083 3.74,1.281 0.188,0.198 10 false 2 6.198,1.615 6.51,1.813 0.313,0.198 10 false *b
*1 Battery *2 Ammeter
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Magnet
*c 5 mm or less - -



c.

Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
1 (NTO) - 2 (NTB) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)
a.

Disconnect the B33 transmission revolution sensor (NT) connector.


b.

Disconnect the B93 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B33-1 (NTO) - B93-125 (NTO) Always Below 1 Ω
B33-2 (NTB) - B93-126 (NTB) Always Below 1 Ω
B33-1 (NTO) or B93-125 (NTO) - Body ground and other terminals Always 10 kΩ or higher
B33-2 (NTB) or B93-126 (NTB) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT