The ECM stores DTC P1589 if deceleration sensor zero point calibration is not performed or failed after system components such as the ECM are replaced.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1589 | Acceleration Sensor Learning Value | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1: 1.
The vehicle speed is 2 km/h (1.2 mph) or more. 2.
Deceleration sensor zero point calibration has not been completed. 3.
When the above abnormal condition is met. 4.
1-trip detection logic DTC Detection Condition 2: 1.
Deceleration sensor zero point calibration is performed. 2.
The learned values of deceleration sensor zero point calibration are abnormal (out of normal range). 3.
When the above abnormal condition is met. 4.
1-trip detection logic |
DTC Detection Condition 1:
Deceleration sensor zero point calibration has not been performed. DTC Detection Condition 2: ·
Vehicle was not stabilized during deceleration sensor zero point calibration. ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
ECM |
Does not come on | DTC stored |
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If CVT oil pressure calibration is performed before deceleration sensor zero point calibration, DTC P1589 is stored. In this case, perform steps *1, *2, *3, *4 and *5 to return the system to normal.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Turn the ignition switch off.*1
Move the shift lever to P and apply the parking brake.*2
Connect the GTS to the DLC3.
Turn the ignition switch to ON.*3
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.*4
| Tester Display |
|---|
| Reset Memory |
Enter the following menus: Powertrain / ECT / Utility / Deceleration Sensor Zero Point Calibration.*5
| Tester Display |
|---|
| Deceleration Sensor Zero Point Calibration |
When "Complete" is displayed on the screen, deceleration sensor zero point calibration is complete.
If "Error" is displayed on the screen, the deceleration sensor circuit may be malfunctioning.
Shaking or vibrating the vehicle during deceleration sensor zero point calibration may cancel calibration. If "Error" is displayed on the screen, perform step *5 again.
If "Error" is displayed on the GTS, read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Deceleration sensor zero point calibration is completed normally | A |
| DTC P1589 is output | B |
A
B
Do not clear the learned values by performing Reset Memory.
Turn the ignition switch off and wait at least 30 seconds.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait at least 2 seconds.
Do not start the engine.
CVT oil pressure calibration is performed with the ignition switch ON (engine stopped). However, calibration cannot be performed under the following conditions:
Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or higher.
CVT oil temperature is -5°C (23°F) or less or 120°C (248°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Start the engine and wait at least 5 seconds.
Start the engine with the shift lever in P.
After starting the engine, do not operate the accelerator pedal.
Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.
During CVT oil pressure calibration, the engine idle speed will increase.
When "Complete" is displayed on the screen, CVT oil pressure calibration is complete.
The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.
| Tester Display |
|---|
| CVT Oil Pressure Calibration |
Check for DTCs again.
| Proceed to |
|---|
| NEXT |
NEXT
Check the yaw rate and acceleration sensor (airbag sensor assembly) for any inclination, bracket deformation or installation clearance.
The yaw rate and acceleration sensor (airbag sensor assembly) is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of G sensor | Min.: 0 V
Max.: 79.998 V |
Displays converted voltage of G sensor
·
2.31 V to 2.69 V: Vehicle on level ground ·
1.88 V to 2.5 V: Decelerating ·
2.5 V to 3.11 V: Accelerating ·
Set to 1.87 V: G sensor malfunction ·
Set to 1.87 V: Communication malfunction |
- |
| Tester Display |
|---|
| G Sensor |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT