Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2015.04–2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

The ECM memory contains programs for normal and sport shift patterns.

By following the programs corresponding to the signals from the combination switch assembly, the park/neutral position switch and other various sensors, the ECM switches the shift control solenoid valves on and off, and controls the transaxle gear ratio.

WIRING DIAGRAM

C278992E06
5.813,3.219 6.281,3.438 0.469,0.219 10 false ECM 5.823,3.021 6.281,3.219 0.458,0.198 10 false A62 5.604,1.385 6.271,1.646 0.667,0.26 10 false PWMS 5.354,1.26 5.615,1.479 0.26,0.219 10 false 57 2.25,2.01 2.698,2.24 0.448,0.229 10 false G60 2.25,2.177 4.156,2.51 1.906,0.333 10 false Combination Switch Assembly 3.396,1.25 4.021,1.479 0.625,0.229 10 false MSW1 2.531,1.24 3.167,1.458 0.635,0.219 10 false MSW2 3.927,1.26 4.083,1.458 0.156,0.198 10 false 2 2.313,1.25 2.469,1.448 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY
a.
C277027C02
1.354,1.792 1.51,1.385 true 2.042,1.771 1.875,1.385 true 1.094,1.844 1.708,2.073 0.615,0.229 10 false MSW2 1.896,1.844 2.51,2.063 0.615,0.219 10 false MSW1 0.104,0.104 0.719,0.302 0.615,0.198 10 false *1
*1 Combination Switch Assembly


Remove the combination switch assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>COMBINATION SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (MSW1) - 4 (MSW2) Combination switch assembly (SPORT) on Below 1 Ω
2 (MSW1) - 4 (MSW2) Combination switch assembly (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)

NG

REPLACE COMBINATION SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BODY GROUND)
a.
C277026C02
0.458,0.948 0.854,1.198 0.396,0.25 2.125,1.74 1.927,1.323 true 0.104,0.083 0.417,0.281 0.313,0.198 10 *a 1.948,1.813 2.5,2.031 0.552,0.219 10 MSW2 0.531,0.979 0.865,1.156 0.333,0.177 10 G60
*a Front view of wire harness connector
(to Combination Switch Assembly)


Disconnect the combination switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G60-4 (MSW2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - ECM)
a.
C277060C01
1.531,0.167 1.896,0.427 0.365,0.26 2.479,1.823 2.229,1.25 true 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 1.604,0.208 1.917,0.406 0.313,0.198 10 A62 2.167,1.906 2.99,2.115 0.823,0.208 10 57 (PWMS)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A62-57 (PWMS) - Body ground Combination switch assembly (SPORT) on Below 1 Ω
A62-57 (PWMS) - Body ground Combination switch assembly (SPORT) off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT