The CVT fluid temperature sensor converts the fluid temperature into a resistance value which is detected by the ECM.
The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.
The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in heavy traffic.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0712 | Transmission Fluid Temperature Sensor "A" Circuit Low Input | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
- 2.
There is a short circuit in the CVT fluid temperature sensor circuit. 3.
0.5 seconds 4.
1 trip detection logic |
·
Short in CVT fluid temperature sensor circuit ·
Continuously variable transaxle assembly ·
ECM |
Comes on | DTC stored |
| P0713 | Transmission Fluid Temperature Sensor "A" Circuit High Input | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
15 minutes or more after starting the engine. 2.
There is an open circuit in the CVT fluid temperature sensor circuit. 3.
0.5 seconds 4.
1 trip detection logic |
·
Open in CVT fluid temperature sensor circuit ·
Continuously variable transaxle assembly ·
ECM |
Comes on | DTC stored |
The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and detects open or short circuits in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature sensor is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the CVT fluid temperature sensor or wiring. The ECM turns on the MIL and stores the DTC.
*1: 150°C (302°F) or higher is indicated regardless of the actual CVT fluid temperature.
*2: -40°C (-40°F) is indicated regardless of the actual CVT fluid temperature.
The CVT fluid temperature can be checked on the GTS display.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| A/T Oil Temperature 1 |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Temperature 1 | CVT fluid temperature sensor value | min.: -40°C (-40°F)
max.: 215°C (419°F) |
·
After stall speed test: Approx. 100°C (212°F) ·
Equal to ambient temperature after cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted. |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is not as specified under Normal Condition |
| Data displayed is as specified under Normal Condition |
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition
| *a | Component without harness connected
(Transmission Wire) |
Disconnect the transmission wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (THO) - 6 (E2) | Always | 79 Ω to 156 kΩ |
| 1 (THO) - Body ground | Always | 10 kΩ or higher |
| 6 (E2) - Body ground | Always | 10 kΩ or higher |
If the resistance is outside the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may be affected.
| CVT Fluid Temperature | Specified Condition |
|---|---|
| 10°C (50°F) | 5 to 8 kΩ |
| 25°C (77°F) | 2.5 to 4.5 kΩ |
| 110°C (230°F) | 0.22 to 0.28 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B75-95 (THO1) - B75-96 (ETHO) | Always | 79 Ω to 156 kΩ |
| B75-95 (THO1) - Body ground | Always | 10 kΩ or higher |
| B75-96 (ETHO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT