Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0962  Pressure Control Solenoid "A" Control Circuit Low (Shift Solenoid Valve DS1)  P0963  Pressure Control Solenoid "A" Control Circuit High (Shift Solenoid Valve DS1)  P0966  Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2)  P0967  Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2)  


DESCRIPTION

Using shift solenoid valve DS1 (inflow to the primary pulley) and shift solenoid valve DS2 (outflow from the primary pulley), the ECM controls the line pressure and fluid volume input to and output from the primary pulley according to the vehicle speed and accelerator pedal angle. As a fail-safe function, if a solenoid is shorted or open, the ECM stops current to the faulty solenoid.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0962 Pressure Control Solenoid "A" Control Circuit Low (Shift Solenoid Valve DS1) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is a short circuit in the shift solenoid valve DS1 circuit.

3.

20 times

4.

1 trip detection logic


·

Short in shift solenoid valve DS1 circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0963 Pressure Control Solenoid "A" Control Circuit High (Shift Solenoid Valve DS1) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is an open circuit in the shift solenoid valve DS1 circuit.

3.

20 times

4.

1 trip detection logic


·

Open in shift solenoid valve DS1 circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0966 Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is a short circuit in the shift solenoid valve DS2 circuit.

3.

20 times

4.

1 trip detection logic


·

Short in shift solenoid valve DS2 circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P0967 Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is an open circuit in the shift solenoid valve DS2 circuit.

3.

20 times

4.

1 trip detection logic


·

Open in shift solenoid valve DS2 circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short circuit in the shift solenoid valve DS1 or DS2 circuit. When there is an open or short circuit in the shift solenoid valve DS1 or DS2 circuit, the ECM detects the problem, illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C277074E01
0.229,4.104 4.26,4.354 4.031,0.25 10 Transmission Wire (Continuously Variable Transaxle Assembly) 0.24,3.875 0.615,4.083 0.375,0.208 10 B37 1.521,2.854 3.229,3.083 1.708,0.229 10 Shift Solenoid Valve DS2 1.521,1.677 3.229,1.906 1.708,0.229 10 Shift Solenoid Valve DS1 3.208,1.104 3.583,1.313 0.375,0.208 10 DS1 3.208,2.271 3.583,2.479 0.375,0.208 10 DS2 3.635,1.385 4.01,1.594 0.375,0.208 10 5 3.625,2.552 4,2.76 0.375,0.208 10 10 5.302,1.385 5.677,1.594 0.375,0.208 10 70 5.302,2.563 5.677,2.771 0.375,0.208 10 69 5.615,1.24 5.99,1.448 0.375,0.208 10 DS1 5.615,2.417 5.99,2.625 0.375,0.208 10 DS2 5.813,4.208 6.188,4.417 0.375,0.208 10 ECM 5.823,4 6.198,4.208 0.375,0.208 10 B75

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Shift Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Shift Position
Data List Display
Shift Status
50004 234 116 416
Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operate the shift solenoid valves to allow the gear ratio to be manually selected [1st - 2nd - 3rd - 4th - 5th]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.


[Vehicle Condition]
Perform at a vehicle speed of 20 km/h (12 mph) or more and 45 km/h (28 mph) or less.

e.

In accordance with the display on the GTS, perform the Active Test.

Result:
Proceed to
Gear ratio does not change
Gear ratio changes




Gear ratio does not change

2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)

Gear ratio changes

4.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)
a.
C199169C06
1.323,0.948 0.76,0.469 true 0.802,1.792 1.323,1.25 true 0.427,0.375 0.865,0.615 0.438,0.24 10 DS1 0.115,0.094 0.427,0.292 0.313,0.198 10 *a 0.448,1.708 0.854,1.938 0.406,0.229 10 DS2
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (DS1) - Body ground 20°C (68°F) 11 to 13 Ω
10 (DS2) - Body ground 20°C (68°F) 11 to 13 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C267934C13
1.49,0.135 1.938,0.385 0.448,0.25 1.333,1.771 0.99,1.01 true 0.635,1.781 0.927,1.01 true 1.604,0.177 2.063,0.375 0.458,0.198 10 B75 0.302,1.854 1.021,2.104 0.719,0.25 10 69 (DS2) 1.115,1.854 1.833,2.104 0.719,0.25 10 70 (DS1) 0.115,0.083 0.385,0.323 0.271,0.24 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-70 (DS1) - Body ground 20°C (68°F) 11 to 13 Ω
B75-69 (DS2) - Body ground 20°C (68°F) 11 to 13 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT