Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2763  Torque Converter Clutch Pressure Control Solenoid Control Circuit High (Shift Solenoid Valve DSU)  P2764  Torque Converter Clutch Pressure Control Solenoid Control Circuit Low (Shift Solenoid Valve DSU)  


DESCRIPTION

The ECM controls the signal sent to shift solenoid valve DSU and performs lock-up clutch pressure control in response to the input torque value.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2763 Torque Converter Clutch Pressure Control Solenoid Control Circuit High (Shift Solenoid Valve DSU) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is being driven.

2.

There is an open circuit in the shift solenoid valve DSU circuit.

3.

Detected 20 times or more consecutively

4.

1 trip detection logic


·

Open in shift solenoid valve DSU circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P2764 Torque Converter Clutch Pressure Control Solenoid Control Circuit Low (Shift Solenoid Valve DSU) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is being driven.

2.

There is a short circuit in the shift solenoid valve DSU circuit.

3.

Detected 20 times or more consecutively

4.

1 trip detection logic


·

Short in shift solenoid valve DSU circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short circuit in the shift solenoid valve DSU circuit. The ECM controls lock-up by turning shift solenoid valve DSU on/off. When there is an open or short circuit in the shift solenoid valve DSU circuit, the ECM detects the problem, illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C251558E09
5.802,3.031 6.167,3.229 0.365,0.198 10 B75 5.792,3.229 6.188,3.458 0.396,0.229 10 ECM 0.167,2.771 0.531,2.969 0.365,0.198 10 B37 0.146,2.969 4.208,3.208 4.063,0.24 10 Transmission Wire (Continuously Variable Transaxle Assembly) 5.615,1.25 6.021,1.458 0.406,0.208 10 DSU 5.323,1.375 5.594,1.594 0.271,0.219 10 71 3.635,1.375 3.844,1.573 0.208,0.198 10 7 3.208,1.125 3.615,1.354 0.406,0.229 10 DSU 1.521,1.74 3.323,1.979 1.802,0.24 10 Shift Solenoid Valve DSU

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DSU)
a.
C199169C07
2.531,1.771 1.906,1.25 true 0.115,0.094 0.427,0.292 0.313,0.198 10 *a 2.635,1.708 3.042,1.938 0.406,0.229 10 DSU
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (DSU) - Body ground 20°C (68°F) 11 to 13 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C267934C15
1.49,0.135 1.938,0.385 0.448,0.25 0.771,1.781 1.063,1.01 true 1.604,0.177 2.063,0.375 0.458,0.198 10 B75 0.458,1.854 1.177,2.104 0.719,0.25 10 71 (DSU) 0.115,0.083 0.385,0.323 0.271,0.24 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-71 (DSU) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT