Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › from 2015.04
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046808 REAR CRANKSHAFT OIL SEAL A

3ZR-FAE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL ENGINE REAR OIL SEAL

a.
A154926E02
3.088,0.392 3.392,0.541 0.304,0.149 10 SST 2.197,0.88 2.962,0.476 2.962,0.476 2.775,1.271 false 3.069,0.472 2.969,0.472 false

Apply MP grease to the lip of a new engine rear oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the rear engine oil seal.

·

Do not allow MP grease to contact the dust seal.




b.

Using SST and a hammer, tap in the engine rear oil seal until its surface is flush with the edges of the cylinder block assembly and crankcase.

SST
09223-15030  
09950-70010  (09951-07100)

NOTICE:
·

Wipe off any extra grease from the crankshaft.

·

Do not tap in the engine rear oil seal at an angle.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

a.

Using SST, hold the crankshaft.

SST
09213-54015  09330-00021  

HINT:

The part number of the installation bolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).



b.

Clean the bolts and bolt holes.


c.
A252955C01
0.563,0.646 0.688,0.646 0.688,0.646 0.813,1.063 false 1.333,0.5 1.583,0.167 1.583,0.167 1.75,0.167 false 2.219,0.667 1.99,0.667 1.99,0.667 1.792,1.031 false 0.354,0.573 0.667,0.729 0.313,0.156 10 *1 1.792,0.083 2.104,0.24 0.313,0.156 10 *2 2.292,0.604 2.604,0.76 0.313,0.156 10 *3 0.083,1.333 0.396,1.49 0.313,0.156 10 *a 2.281,1.333 2.594,1.49 0.313,0.156 10 *b
*1 Front Drive Plate Spacer (Reversible)
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
*a Engine Side
*b Transaxle Side


Install the front drive plate spacer.


d.

Install the drive plate and ring gear sub-assembly and the rear drive plate spacer to the crankshaft.

HINT:
·

The front drive plate spacer is reversible.

·

As the rear drive plate spacer and the drive plate and ring gear sub-assembly are not reversible. Be sure to install them so that they are facing in the direction shown in the illustration.




e.
A192239C31
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A293588N01
2.115,0.521 2.271,0.719 0.156,0.198 10 1 1.708,1.646 1.865,1.844 0.156,0.198 10 2 2.385,0.885 2.542,1.083 0.156,0.198 10 3 1.385,1.323 1.542,1.521 0.156,0.198 10 4 2.396,1.26 2.552,1.458 0.156,0.198 10 5 1.333,0.865 1.49,1.063 0.156,0.198 10 6 2.167,1.542 2.323,1.74 0.156,0.198 10 7 1.583,0.542 1.74,0.74 0.156,0.198 10 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate and ring gear sub-assembly.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.
A234914N09
0.906,3 2.469,3 true 1.396,1.885 2.302,0.583 2.302,0.583 2.927,0.583 true 2.958,0.49 3.26,0.656 0.302,0.167 10 SST 0.542,2.906 0.844,3.073 0.302,0.167 10 SST

Using SST, hold the crankshaft.

SST
09213-54015  09330-00021  

HINT:

The part number of the installation bolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).



b.

Clean the bolts and bolt holes.


c.
A192239C31
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply adhesive to 2 or 3 threads at the end of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A297256N01
1.99,0.604 2.146,0.802 0.156,0.198 10 1 2.219,0.854 2.375,1.052 0.156,0.198 10 3 2.229,1.188 2.385,1.385 0.156,0.198 10 5 2.042,1.479 2.198,1.677 0.156,0.198 10 7 1.635,1.521 1.792,1.719 0.156,0.198 10 2 1.385,1.24 1.542,1.438 0.156,0.198 10 4 1.396,0.865 1.552,1.063 0.156,0.198 10 6 1.646,0.604 1.802,0.802 0.156,0.198 10 8

Using several steps, tighten the 8 bolts uniformly in the sequence shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


e.

Mark the top of each bolt with paint.


f.

Tighten the 8 bolts 90°.


g.

Check that the paint marks are now at a 90° angle to the top.


h.

Check that the crankshaft turns smoothly.


Hide 31250 4.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 5.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 6.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 30400 7.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 30300 8.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)