Home › Drivetrain › EB61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY › 2012.12–2015.10
RM3090E _52 Drivetrain _008758 EB61F MANUAL TRANSMISSION / TRANSAXLE _0050281 MANUAL TRANSAXLE ASSEMBLY A

EB61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 36100A 1.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT


a.

Clean the bolt holes.


b.

Apply adhesive 1324 to 2 or 3 threads on one half of a new transfer and transaxle setting stud bolt A as shown in the illustration.

C299986C01
2.406,0.521 2.563,0.719 0.156,0.198 10 false A 4.438,0.406 4.594,0.604 0.156,0.198 10 false A 2.5,2.104 2.656,2.302 0.156,0.198 10 false B 6.063,0.49 6.219,0.688 0.156,0.198 10 false B 0.667,2.146 1.01,2.354 0.344,0.208 10 false *a 0.677,2.385 1.021,2.594 0.344,0.208 10 false *b
*a Toyota Genuine Adhesive 1324 *b Sealant


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Do not apply adhesive 1324 to the ends of the stud bolt.

·

Install the stud bolt immediately after applying adhesive to prevent the adherence of foreign matter.




c.

Install the 2 new transfer and transaxle setting stud bolts to the transaxle case positions shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the stud bolt so that the side that has sealant and adhesive is facing the automatic transaxle assembly.


HINT:

Stud bolt length:

Stud bolt A: 69 mm (2.72 in.)

Stud bolt B: 47 mm (1.85 in.)



Hide 36100 2.INSTALL TRANSFER ASSEMBLY

Hide 33403K 3.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Coat a new O-ring with gear oil.


b.

Install the O-ring to the speedometer driven hole cover sub-assembly.


c.

Install the speedometer driven hole cover sub-assembly to the transaxle case with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 31400 4.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31407B 7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31490 8.INSTALL CLUTCH ACCUMULATOR ASSEMBLY

Hide 12321A 9.INSTALL REAR ENGINE MOUNTING BRACKET

C277913C01
2.417,1.688 2.573,1.885 0.156,0.198 10 2 1.896,1.75 2.052,1.948 0.156,0.198 10 3 1.625,0.271 1.781,0.469 0.156,0.198 10 4 2.563,0.094 3.271,0.302 0.708,0.208 10 1 (*a), 5
*a Temporarily


a.

Temporarily install the rear engine mounting bracket with the 4 bolts.


b.

Tighten the 4 bolts of the rear engine mounting bracket in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12325A 10.INSTALL ENGINE MOUNTING BRACKET LH

C279718C01
1.052,0.615 1.208,0.813 0.156,0.198 10 4 0.99,1.427 1.146,1.625 0.156,0.198 10 2 2.177,0.677 3.052,0.906 0.875,0.229 10 1 (*a), 5 2.49,1.427 2.646,1.625 0.156,0.198 10 3
*a Temporarily


a.

Clean the bolts and the installation holes in the engine mounting bracket LH.


b.

Apply adhesive to the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Temporarily install the engine mounting bracket LH with the 4 bolts.


d.

Tighten the 4 bolts of the engine mounting bracket LH in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12311A 11.INSTALL FRONT ENGINE MOUNTING BRACKET

C279719C01
0.281,0.073 1,0.271 0.719,0.198 10 1 (*a), 5 1.708,0.115 1.865,0.313 0.156,0.198 10 3 1.094,1.771 1.25,1.969 0.156,0.198 10 2 1.813,0.875 1.969,1.073 0.156,0.198 10 4
*a Temporarily


a.

Temporarily install the front engine mounting bracket with the 4 bolts.


b.

Tighten the 4 bolts of the front engine mounting bracket in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 30300 12.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.

Align the input shaft with the clutch disc and install the manual transaxle to the engine.

NOTICE:
·

Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle onto the engine with the contact surfaces of the engine and transaxle flat against each other.

·

Insert the dowel pins into the dowel holes securely so that the end face of the transaxle assembly fits close against the engine assembly before tightening the bolts.




b.
C277914C01
2.417,1.979 2.573,2.177 0.156,0.198 10 B 2.854,1.74 3.01,1.938 0.156,0.198 10 B 1.688,1.979 1.844,2.177 0.156,0.198 10 B 0.969,1.854 1.125,2.052 0.156,0.198 10 B 0.833,0.604 0.99,0.802 0.156,0.198 10 B 0.813,0.094 1.177,0.302 0.365,0.208 10 A: 2 2.51,0.052 3.323,0.24 0.813,0.188 10 A: 1(*a), 4 2.844,0.333 3.208,0.542 0.365,0.208 10 A: 3
*a Temporarily


Temporarily install the manual transaxle assembly with the bolt (*a).


c.

Tighten the 3 bolts labeled A in the order shown in the illustration, and then install the 5 bolts labeled B.

Torque:
for Bolt A : 38 N*m (387 kgf*cm, 28 ft.*lbf)
for Bolt B : 40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Connect the back-up light switch connector and install the engine wire to the manual transaxle assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.

Connect the clamp with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)