Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o Occupant Classification System) › 2015.04–2015.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0049192 AIRBAG SYSTEM(w/o Occupant Classification System) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C279978E02
0.531,4.417 4.198,4.615 3.667,0.198 10 false : CAN Communication Line 1.271,4.094 1.813,4.281 0.542,0.188 10 false DLC3 1.25,3.927 1.792,4.115 0.542,0.188 10 false G14 1.802,3.417 2.344,3.604 0.542,0.188 10 false TC 1.271,3.438 1.813,3.625 0.542,0.188 10 false CG 2.052,3.323 2.594,3.51 0.542,0.188 10 false 13 5.573,3.823 6.115,4.01 0.542,0.188 10 false G92 1.021,3.302 1.563,3.49 0.542,0.188 10 false 4 5.573,4 7.104,4.188 1.531,0.188 10 false Airbag Sensor Assembly 5.771,0.406 6.313,0.594 0.542,0.188 10 false 22 5.771,0.958 6.313,1.146 0.542,0.188 10 false 13 6.01,0.542 6.552,0.729 0.542,0.188 10 false CANL 6.021,1.115 6.563,1.302 0.542,0.188 10 false CANH 2.417,0.333 2.958,0.521 0.542,0.188 10 false 26*1, *2 2.385,0.917 2.927,1.104 0.542,0.188 10 false 13*1, *2 2.417,1.344 2.958,1.531 0.542,0.188 10 false 23*1 2.063,1.49 2.604,1.677 0.542,0.188 10 false 26*3 2.417,1.677 2.958,1.865 0.542,0.188 10 false A62 2.083,1.667 2.625,1.854 0.542,0.188 10 false A61 1.542,0.531 2.083,0.719 0.542,0.188 10 false CANL 1.531,1.094 2.073,1.281 0.542,0.188 10 false CANH 1.792,1.677 2.333,1.865 0.542,0.188 10 false TC 1.49,2.448 2.031,2.635 0.542,0.188 10 false ECM 2.896,3.75 5.01,3.948 2.115,0.198 10 false *1: for 2AR-FE, 3ZR-FE 2.896,4.375 5.063,4.573 2.167,0.198 10 false *3: for Diesel Engine 2.417,1.125 2.958,1.313 0.542,0.188 10 false A62 2.406,0.552 2.948,0.74 0.542,0.188 10 false A62 2.083,1.135 2.625,1.323 0.542,0.188 10 false A61 2.083,0.552 2.625,0.74 0.542,0.188 10 false A61 2.083,0.344 2.625,0.531 0.542,0.188 10 false 6*3 2.083,0.917 2.625,1.104 0.542,0.188 10 false 7*3 2.417,1.49 2.958,1.677 0.542,0.188 10 false 33*2 2.906,4.042 5.021,4.24 2.115,0.198 10 false *2: for 3ZR-FAE

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.


Result:
Proceed to
DTCs are output (for LHD)
DTCs are output (for RHD)
DTC is not output




DTCs are output (for LHD)

DTCs are output (for RHD)

DTC is not output

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.

C279979C02
1,0.167 1.333,0.417 0.333,0.25 2.385,0.438 2.719,0.688 0.333,0.25 4.594,0.583 4.938,0.833 0.344,0.25 1.313,1.135 1.938,1.438 true 3.948,1.021 4.469,1.354 true 6.135,0.875 6.656,1.208 true 3.385,1.135 2.938,1.438 true 1.052,0.198 1.51,0.396 0.458,0.198 10 false G14 2.427,0.469 2.885,0.667 0.458,0.198 10 false A62 4.625,0.615 5.073,0.885 0.448,0.271 10 false A61 0.094,0.083 0.552,0.281 0.458,0.198 10 false *a 3.448,0.135 3.906,0.333 0.458,0.198 10 false *b 1.99,1.365 2.448,1.563 0.458,0.198 10 false TC 4.531,1.26 4.99,1.458 0.458,0.198 10 false TC*C 6.719,1.156 7.042,1.354 0.323,0.198 10 false TC 5.865,0.156 6.323,0.354 0.458,0.198 10 false *b 2.563,1.406 3.021,1.604 0.458,0.198 10 false TC*D 2.781,0.479 3.24,0.677 0.458,0.198 10 false *A 4.99,0.583 5.448,0.781 0.458,0.198 10 false *B
*A for Gasoline *B for Diesel
*C for 2AR-FE, 3ZR-FE *D for 3ZR-FAE
*a Front view of DLC3 *b Front view of wire harness connector
(to ECM)



b.

Disconnect the A62*1 or A61*2 connector from the ECM.

*1: for Gasoline Engine

*2: for Diesel Engine



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FE
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-23 (TC) Always Below 1 Ω

for 3ZR-FAE
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-33 (TC) Always Below 1 Ω


for Diesel
Tester Connection Condition Specified Condition
G14-13 (TC) - A61-26 (TC) Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509C04
1.458,0.281 1.844,0.51 0.385,0.229 1.635,1.073 1.24,1.698 false 0.094,0.125 0.313,0.354 0.219,0.229 10 false *a 1.021,1.75 1.302,1.938 0.281,0.188 10 false CG 1.51,0.302 1.802,0.448 0.292,0.146 10 false G14
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
C279980C02
1.448,0.094 1.875,0.344 0.427,0.25 1.542,1.875 1.969,2.125 0.427,0.25 2.073,1.083 2.552,0.573 true 2,2.625 2.479,2.115 true 0.823,0.99 1.375,1.219 true 1.51,0.125 1.969,0.323 0.458,0.198 10 false A62 1.604,1.885 2.063,2.083 0.458,0.198 10 false A61 0.146,0.104 0.604,0.302 0.458,0.198 10 false *a 0.188,1.854 0.646,2.052 0.458,0.198 10 false *a 2.604,0.438 3.063,0.635 0.458,0.198 10 false TC*C 2.521,1.979 2.979,2.177 0.458,0.198 10 false TC 0.469,0.823 0.927,1.021 0.458,0.198 10 false TC*D 1.927,0.115 2.385,0.313 0.458,0.198 10 false *A 2.063,1.906 2.521,2.104 0.458,0.198 10 false *B
*A for Gasoline Engine
*B for Diesel Engine
*C for 2AR-FE, 3ZR-FE
*D for 3ZR-FAE
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FE
Tester Connection Condition Specified Condition
A62-23 (TC) - Body ground Always Below 1 Ω

for 3ZR-FAE
Tester Connection Condition Specified Condition
A62-33 (TC) - Body ground Always Below 1 Ω

for Diesel
Tester Connection Condition Specified Condition
A61-26 (TC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU