Home › General › INTRODUCTION › REPAIR INSTRUCTION › 2015.04–2015.10
RM3090E _V1 General _008731 INTRODUCTION _0049918 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED


Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for 1AD-FTV:

Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes)


Stop and start system (Click here)
for 3ZR-FAE:

Drive the vehicle until stop and start control is permitted (approximately 5 to 40 minutes)


Stop and start system (Click here)
Reset back door close position
·

Power back door function

·

Back door closer function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation receiver assembly requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed Link
for 1AD-FTV:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 1AD-FTV:

Engine assembly


·

Crank Time Compensation Reset

·

Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 1AD-FTV:

No. 1 crankshaft position sensor plate


Crank Time Compensation Reset
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 1AD-FTV:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 1AD-FTV:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 1AD-FTV:

Exhaust manifold converter sub-assembly (DPF catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 1AD-FTV:

Injector assembly


·

Injector Compensation

·

Pilot Quantity Learning


DTC is output.
for 1AD-FTV:

ECM


Register VIN DTC P0630 is input (Click here)
for 1AD-FTV:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly

·

Turbocharger sub-assembly


ECD System initialization Engine start (Click here)
for 2AD-FHV:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FHV:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FHV:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FHV:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 2AD-FHV
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FHV:

Exhaust manifold converter sub-assembly (DPNR catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPNR thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 2AD-FHV:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FHV:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FHV:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AD-FTV, CCo:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FTV, CCo:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FTV, CCo:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FTV, CCo:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FTV, CCo:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FTV, CCo:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FTV, CCo:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AD-FTV, DPF:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FTV, DPF:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FTV, DPF

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FTV, DPF:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 2AD-FTV, DPF:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FTV, DPF:

Exhaust manifold converter sub-assembly (DPF catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 2AD-FTV, DPF:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FTV, DPF:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FTV, DPF:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AR-FE, w/ Canister Pump Module:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AR-FE, w/o Canister Pump Module:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AR-FE, w/ Canister Pump Module:
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 2AR-FE, w/o Canister Pump Module:
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 3ZR-FAE:

ECM


Register VIN DTC P0630 is input (Click here)
for 3ZR-FAE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Continuously variable valve lift controller assembly

·

Cylinder head sub-assembly

·

Camshaft housing sub-assembly

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 3ZR-FE:

ECM


Register VIN DTC P0630 is input (Click here)
for 3ZR-FE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft

(for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
·

Lane departure warning camera

·

Windshield glass


Adjust lane departure warning camera DTCs are output (Click here)
w/ Stop and Start System:

Engine stop and start ECU


·

Upload the number of starter operations

·

Reset air conditioning information

·

Learning of the air conditioning information

·

Clear the zero point calibration data

·

Perform zero point calibration of the deceleration sensor


Stop and start system for 1AD-FTV:(Click here)
for 3ZR-FAE:(Click here)
w/ Stop and Start System:

Starter assembly


Clear the number of starter operations
w/ Stop and Start System:

Air conditioning amplifier assembly


·

Reset air conditioning information

·

Learning of the air conditioning information


w/ Stop and Start System:

Airbag sensor assembly


·

Clear the zero point calibration of the deceleration sensor

·

Perform zero point calibration of the deceleration sensor


w/ Stop and Start System, for 3ZR-FAE:
·

Continuously variable transaxle assembly

·

CVT fluid


Bleed the oil pump assembly with motor (continuously variable transaxle assembly)
w/ Stop and Start System, for 3ZR-FAE:

Vehicle with a nonspecified battery


Perform battery typeswitching
for U660F:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into TCM

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U660F:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U660F:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow TCM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U660F:

TCM (If possible, read the transaxle compensation code from the previous TCM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new TCM)

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U760E:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow ECM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

ECM (If possible, read the transaxle compensation code from the previous ECM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new ECM)

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U760F:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow ECM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

ECM (If possible, read the transaxle compensation code from the previous ECM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new ECM)

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for K111:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly) (w/ VSC)

·

Deceleration sensor (w/o VSC)

·

Skid control ECU (Brake actuator assembly) (w/o VSC)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K111F:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly) (w/ VSC)

·

Deceleration sensor (w/o VSC)

·

Skid control ECU (Brake actuator assembly) (w/o VSC)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K114F:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K114F:
·

Continuously variable transaxle assembly

·

CVT fluid


Bleed the oil pump assembly with motor Stop and start system
for K114F:

CVT fluid


ATF Thermal Degradation Estimate Reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
·

4WD ECU assembly

HINT:

When replacing the 4WD ECU assembly with a new one, it is not necessary to perform initialization.


·

Acceleration sensor (airbag sensor assembly) (w/ VSC)

·

Deceleration sensor (w/o VSC)


Clear zero point calibration data Dynamic torque control 4WD/AWD system (Click here)
·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


·

Transmitter ID registration

·

Initialization


Tire pressure warning system for Registration:(Click here)
for Initialization:(Click here)
Skid control ECU (brake actuator assembly) Yaw rate and acceleration sensor zero point calibration. Vehicle stability control system (Click here)
Yaw rate and acceleration sensor (airbag sensor assembly)
·

Clearing zero point calibration data.

·

Yaw rate and acceleration sensor zero point calibration.

·

Acceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).


Vehicle stability control system (Click here)
Wheel alignment adjustment
·

Clearing zero point calibration data.

·

Yaw rate and acceleration sensor zero point calibration.


Vehicle stability control system (Click here)
Power steering ECU assembly Assist map writing Power steering system (Click here)
w/ Parking Assist Monitor System, for Camera built-in ECU:

Spiral with sensor cable sub-assembly


Steering angle setting Parking assist monitor system (for Camera built-in ECU) (Click here)
w/ Parking Assist Monitor System, for Camera built-in ECU:

Suspension, tires, etc.


Back camera position setting
w/ Parking Assist Monitor System, for Camera built-in ECU:

Television camera assembly


Parking assist monitor system initialization
w/ Entry and Start System:
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)*1

·

ECM

·

Steering lock ECU (steering lock actuator assembly)

·

Electrical key transmitter sub-assembly


Registration
·

Wireless door lock operation

·

Entry operation

·

Engine starting

·

Steering unlock


Refer to the Service Bulletin for the registration method
w/o Entry and Start System:
·

Transponder key ECU assembly

·

ECM

·

Electrical key transmitter sub-assembly


Registration Engine starting Refer to the Service Bulletin for the registration procedure
w/o Entry and Start System:
·

Door control transmitter

·

Door control receiver


Register recognition code Wireless door lock operation (Click here)
w/ Blocking System:
·

Instrument panel integration antenna assembly

·

Telephone transceiver assembly

·

Mayday battery


Registration Engine starting Refer to the Service Bulletin for the registration procedure
·

Occupant detection ECU

·

Front seat assembly RH (occupant classification sensor)


·

Zero point calibration

·

Sensitivity check


·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)
for Automatic Air Condition System:
·

Air conditioning amplifier assembly

·

No. 1 Air conditioning radiator damper servo sub-assembly

·

No. 2 Air conditioning radiator damper servo sub-assembly

·

No. 3 Air conditioning radiator damper servo sub-assembly

·

No. 1 Blower mode damper servo sub-assembly


Initialization servo motor Initialization servo motor (Click here)
w/ Jam Protection Function:
·

Power window regulator motor assembly

·

Power window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up/down function

·

Jam protection function


(Click here)
·

Sliding roof drive gear sub-assembly (sliding roof ECU)

·

Sliding roof glass sub-assembly

·

Sliding roof drive cable sub-assembly


Initialize sliding roof ECU (pulse sensor initial position setting)
·

Automatic slide open/close and tilt up/down function of sliding roof

·

Jam protection function

·

Operation function after ignition off

·

Sliding roof open warning


(Click here)
w/ Power Back Door System:

Back door lock assembly


Initialize back door closer system Back door lock operation (Click here)
w/ Power Back Door System:

Multiplex network door ECU


Initialize power back door system Power back door system (Click here)
·

Height control sensor

·

Height leveling ECU


Height leveling ECU initialization Height leveling function (Click here)


*1: w/ Multi-information Display (Dot Display Type)