Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1072  Plausibility Test with Environment Pressure  P1131  Plausibility Test with Intake Air Pressure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1072 Plausibility Test with Environment Pressure The fault is set whenever the absolute difference between the pressure upstream of the turbine and the ambient pressure in after-run mode is greater than 120 hPa (12 kPa).
(3 trip detection logic)
HINT:

After-run mode is the period between IG OFF and shut down of ECM (EFI MAIN NO. 1 relay off), when the ECM saves certain values and performs certain checks.


·

Open or short in exhaust gas pressure sensor circuit

·

Exhaust gas pressure sensor

·

ECM


Does not come on DTC stored
P1131 Plausibility Test with Intake Air Pressure The fault code is set when the absolute difference between the pressure upstream of the turbine and the charging pressure in after-run mode is greater than 150 mbar (15 kPa).
(3 trip detection logic)
HINT:

After-run mode is the period between IG OFF and shut down of ECM (EFI MAIN NO. 1 relay off), when the ECM saves certain values and performs certain checks.


·

Open or short in exhaust gas pressure sensor circuit

·

Exhaust gas pressure sensor

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1072
P1131
·

Absolute Turbine Upstream Pressure

·

Atmosphere Pressure



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ABSOLUTE TURBINE UPSTREAM PRESSURE AND ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Absolute Turbine Upstream Pressure and Atmosphere Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
Absolute Turbine Upstream Pressure
50003 371 5,119

d.

Read the value immediately after stopping the engine.

Standard:

Difference between the Absolute Turbine Upstream Pressure and Atmosphere Pressure is within 8 kPa or less.


HINT:

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.



Result:
Proceed to
OK
NG



OK

2.CHECK EXHAUST GAS PRESSURE SENSOR AIR HOSE CONNECTION

NG

6.REPLACE EXHAUST GAS PRESSURE SENSOR
2.CHECK EXHAUST GAS PRESSURE SENSOR AIR HOSE CONNECTION
a.

Check that the exhaust gas pressure sensor air hose is securely installed.

OK:

Part is securely installed.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST GAS PRESSURE SENSOR - ECM)

NG

4.REPAIR AIR HOSE
3.CHECK HARNESS AND CONNECTOR (EXHAUST GAS PRESSURE SENSOR - ECM)
a.

Disconnect the exhaust gas pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B130-1 (VC) - B112-24 (VCPE) Always Below 1 Ω
B130-2 (PEXM) - B112-103 (PEXM) Always Below 1 Ω
B130-3 (E2) - B112-135 (EPEM) Always Below 1 Ω
B130-1 (VC) or B112-24 (VCPE) - Body ground Always 10 kΩ or higher
B130-2 (PEXM) or B112-103 (PEXM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPAIR AIR HOSE

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR AIR HOSE
a.

Repair the air hose.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE EXHAUST GAS PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END