Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0471  Exhaust Pressure Sensor "A" Circuit Range / Performance  P0472  Exhaust Pressure Sensor "A" Circuit Low  P0473  Exhaust Pressure Sensor "A" Circuit High  


DESCRIPTION

The exhaust gas pressure sensor is fixed to the engine by a holder to protect it from high temperatures.

The exhaust gas pressure sensor is connected to the exhaust manifold via a hose and pipe, and detects the exhaust gas pressure before exhaust turbocharger.

The exhaust gas pressure sensor is supplied with 5 V from the ECM and has a measurement range between 100 kPa (1.01 bar) to 500 kPa (5.1 bar). This is equivalent to 1.0 to 4.5 V.

A342515E02
0.698,0.833 0.885,0.115 0.885,0.115 1.094,0.115 true 3.438,1.208 3.125,0.448 3.125,0.448 2.948,0.448 true 1.167,0.042 5.292,0.24 4.125,0.198 10 false Exhaust Gas Pressure Sensor 1.854,0.365 5.979,0.563 4.125,0.198 10 false Exhaust Manifold 3.979,0.313 6.979,0.51 3,0.198 10 false Property of Output Voltage: 4.396,0.677 7.156,0.896 2.76,0.219 10 false Exhaust Pressure Voltage (V): 4.083,1.438 7.156,1.656 3.073,0.219 10 false 4.5 4.083,2.302 7.156,2.521 3.073,0.219 10 false 1.0 4.656,2.74 5.063,3.083 0.406,0.344 10 false 100 6.156,2.75 6.563,3.094 0.406,0.344 10 false 500 5.24,3.083 7.156,3.302 1.917,0.219 10 false Exhaust Gas Pressure (kPa)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0471 Exhaust Pressure Sensor "A" Circuit Range / Performance Either condition is met (3 trip detection logic):
·

The difference between the standard pressure value calculated from the turbo pressure and ambient pressure and the value from the exhaust gas pressure sensor exceeds 200 mbar (20 kPa).

·

The difference between the standard pressure value calculated from the turbo pressure and ambient pressure and the value from the exhaust gas pressure sensor exceeds -200 mbar (-20 kPa).


HINT:

The difference of the standard pressure value (turbo pressure and ambient pressure) is 60 mbar (6 kPa) or less.


·

Open or short in exhaust gas pressure sensor circuit

·

Exhaust gas pressure sensor

·

ECM


Comes on DTC stored
P0472 Exhaust Pressure Sensor "A" Circuit Low Exhaust gas pressure sensor output voltage is 0.2 V or less.
(3 trip detection logic)
·

Open or short in exhaust gas pressure sensor circuit

·

Exhaust gas pressure sensor

·

ECM


Comes on DTC stored
P0473 Exhaust Pressure Sensor "A" Circuit High Exhaust gas pressure sensor output voltage is 4.9 V or more.
(3 trip detection logic)
·

Open or short in exhaust gas pressure sensor circuit

·

Exhaust gas pressure sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0471
P0472
P0473
Sensed Value of the Pressure at TrbnUs
Absolute Turbine Upstream Pressure

WIRING DIAGRAM

A165731E75
0.438,2.063 1.021,2.313 0.583,0.25 10 false B130 0.438,2.219 2.708,2.573 2.271,0.354 10 false Exhaust Gas Pressure Sensor 6.042,2.063 6.594,2.271 0.552,0.208 10 false B112 6.052,2.219 6.479,2.396 0.427,0.177 10 false ECM 1.542,1.583 1.948,1.792 0.406,0.208 10 false E2 1.333,1.042 1.823,1.229 0.49,0.188 10 false PEXM 1.521,0.469 2,0.688 0.479,0.219 10 false VC 5.698,1.583 6.24,1.844 0.542,0.26 10 false EPEM 5.698,1.031 6.333,1.281 0.635,0.25 10 false PEXM 5.698,0.448 6.344,0.74 0.646,0.292 10 false VCPE 1.844,0.354 1.969,0.531 0.125,0.177 10 false 1 1.844,0.927 1.969,1.104 0.125,0.177 10 false 2 1.844,1.469 1.969,1.646 0.125,0.177 10 false 3 5.406,0.354 5.844,0.729 0.438,0.375 10 false 24 5.344,0.927 5.719,1.146 0.375,0.219 10 false 103 5.344,1.458 5.708,1.677 0.365,0.219 10 false 135

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EXHAUST GAS PRESSURE SENSOR - ECM)
a.

Disconnect the exhaust gas pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B130-1 (VC) - B112-24 (VCPE) Always Below 1 Ω
B130-2 (PEXM) - B112-103 (PEXM) Always Below 1 Ω
B130-3 (E2) - B112-135 (EPEM) Always Below 1 Ω
B130-1 (VC) or B112-24 (VCPE) - Body ground Always 10 kΩ or higher
B130-2 (PEXM) or B112-103 (PEXM) - Body ground Always 10 kΩ or higher
B130-3 (E2) or B112-135 (EPEM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
a.
A351158C23
0.302,1.146 0.75,1.365 0.448,0.219 0.948,1.792 1.354,1.281 true 2.438,1.792 2.083,1.281 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.365,1.177 0.833,1.375 0.469,0.198 10 false B130 0.865,1.833 1.333,2.031 0.469,0.198 10 false VC 2.385,1.844 2.854,2.042 0.469,0.198 10 false E2
*a Front view of wire harness connector
(to Exhaust Gas Pressure Sensor)


Disconnect the exhaust gas pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B130-1 (VC) - B130-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE EXHAUST GAS PRESSURE SENSOR

NG

5.REPLACE ECM
3.REPLACE EXHAUST GAS PRESSURE SENSOR
a.

Replace the exhaust gas pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0471, P0472 OR P0473)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0471, P0472 OR P0473)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0471, P0472 or P0473 B




A

END

B

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END