Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  B22C0  BBC Overcurrent  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU.

The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied to the audio and visual system, etc. drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage at 13.5 V when its mode changes from standby mode to compensation mode. If the backup boost converter cannot maintain the voltage at the specified level when the engine is restarted by stop and start control, the engine stop and start ECU stores a DTC and blinks the stop and start cancel indicator light. The stop and start cancel indicator light will remain blinking during the trip in which the malfunction occurred.

HINT:

A relay function and fuse function are provided in the backup boost converter. If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset*1 when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*1: A semiconductor fuse self-resets according to electric signals.

The backup boost converter supplies power to:
·

Main body ECU (multiplex network body ECU)

·

Skid control ECU (Brake actuator assembly)

·

Spiral with sensor cable sub-assembly

·

Power steering ECU assembly

·

Combination meter assembly

·

Radio receiver assembly, radio and display receiver assembly or navigation receiver assembly

·

Inner rear view mirror assembly

·

Lane departure warning camera

·

Tire pressure warning ECU and receiver

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH

·

Parking assist ECU

·

Driving support ECU assembly

·

Millimeter wave radar sensor assembly

·

Network Gateway ECU



DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
B22C0 BBC Overcurrent The following condition continues for 1 second or more (1 trip detection logic):
·

Overcurrent is detected at the B41, B42 and IG41 terminals in the engine stop and start ECU


·

Engine stop and start ECU

·

Wire harness or connector

·

Power steering ECU assembly

·

Main body ECU (Multiplex network body ECU)

·

Radio receiver assembly (for Radio Receiver Type)

·

Navigation receiver assembly (for Navigation Receiver Type)

·

Radio and display receiver assembly (for Radio and Display Receiver Type)

·

Inner rear view mirror assembly (w/ EC Mirror)

·

Lane departure warning camera (w/ Lane Departure Alert System)

·

Tire pressure warning ECU and receiver (w/ Tire Pressure Warning System)

·

Blind spot monitor sensor LH (w/ Blind Spot Monitor System)

·

Blind spot monitor sensor RH (w/ Blind Spot Monitor System)

·

Driving support ECU assembly (w/ Dynamic Radar Cruise Control System)

·

Millimeter wave radar sensor assembly (w/ Dynamic Radar Cruise Control System)

·

Parking Assist ECU (w/ Panoramic View Monitor System)

·

Network Gateway ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A375260E01
0.115,0.094 2.208,0.375 2.094,0.281 12 false w/ Entry and Start System: 4.427,0.448 5.438,0.646 1.01,0.198 10 false BBC 4.26,0.156 4.49,0.375 0.229,0.219 10 false 1 4.75,0.156 4.979,0.375 0.229,0.219 10 false 2 3.885,0.896 4.896,1.094 1.01,0.198 10 false BBC NO. 2 4.333,0.625 4.563,0.844 0.229,0.219 10 false 2 3.906,0.615 4.135,0.833 0.229,0.219 10 false 1 5.75,0.75 6.365,0.948 0.615,0.198 10 false BIN2 5.365,0.74 5.823,0.938 0.458,0.198 10 false A86 5.438,0.542 5.667,0.76 0.229,0.219 10 false 1 5.74,0.302 6.354,0.5 0.615,0.198 10 false BIN1 5.385,0.292 5.844,0.49 0.458,0.198 10 false A86 5.448,0.104 5.604,0.302 0.156,0.198 10 false 3 5.74,1.458 6.198,1.656 0.458,0.198 10 false IG2 5.385,1.281 5.698,1.479 0.313,0.198 10 false 18 5.375,1.479 5.833,1.677 0.458,0.198 10 false G87 2.438,1.344 2.594,1.542 0.156,0.198 10 false 5 1.667,1.344 1.823,1.542 0.156,0.198 10 false 3 2.438,1.698 2.667,1.917 0.229,0.219 10 false 1 1.667,1.688 1.896,1.906 0.229,0.219 10 false 2 1.115,1.635 1.573,1.833 0.458,0.198 10 false IG2 1.958,2.115 2.417,2.313 0.458,0.198 10 false IG2 3.24,2.542 3.698,2.74 0.458,0.198 10 false G82 3.323,2.354 3.479,2.552 0.156,0.198 10 false 9 1.802,3.281 2.26,3.479 0.458,0.198 10 false G82 1.885,3.083 2.115,3.302 0.229,0.219 10 false 2 3.25,2.917 3.708,3.115 0.458,0.198 10 false G84 3.323,2.74 3.479,2.938 0.156,0.198 10 false 6 3.323,3.115 3.479,3.313 0.156,0.198 10 false 4 3.25,3.281 3.708,3.479 0.458,0.198 10 false G84 2.854,2.542 3.469,2.74 0.615,0.198 10 false IG2D 2.854,2.906 3.469,3.104 0.615,0.198 10 false IG1D 2.781,3.281 3.396,3.479 0.615,0.198 10 false ACCD 2.146,3.271 2.458,3.469 0.313,0.198 10 false +B 1.938,3.677 3.479,4.344 1.542,0.667 10 false Certification ECU (Smart Key ECU Assembly) 0.979,3.458 1.438,3.656 0.458,0.198 10 false AM2 4.354,4.594 4.667,4.792 0.313,0.198 10 false 3C 4.49,4.385 4.802,4.583 0.313,0.198 10 false 37 3.823,4.385 4.135,4.583 0.313,0.198 10 false 14 3.708,4.583 4.021,4.781 0.313,0.198 10 false 3B 4.021,5.042 4.479,5.24 0.458,0.198 10 false IGN 3.74,5.625 4.198,5.823 0.458,0.198 10 false ACC 4.427,5.479 4.74,5.677 0.313,0.198 10 false 3D 4.427,5.292 4.74,5.49 0.313,0.198 10 false 50 2.969,6.104 3.427,6.302 0.458,0.198 10 false ACC 5.74,5.479 6.198,5.677 0.458,0.198 10 false ACC 5.375,5.469 5.833,5.667 0.458,0.198 10 false G87 5.417,5.281 5.729,5.479 0.313,0.198 10 false 19 4.417,5.833 4.729,6.031 0.313,0.198 10 false 3C 4.417,5.656 4.729,5.854 0.313,0.198 10 false 45 3.646,6.688 4.563,6.885 0.917,0.198 10 false EPS-IG 4.406,6.542 4.719,6.74 0.313,0.198 10 false 3D 4.417,6.344 4.729,6.542 0.313,0.198 10 false 43 4.406,6.906 4.719,7.104 0.313,0.198 10 false 3C 4.406,6.719 4.719,6.917 0.313,0.198 10 false 43 2.802,7.188 3.521,7.396 0.719,0.208 10 false IG1 NO. 1 1.938,6.906 2.25,7.104 0.313,0.198 10 false 3D 1.979,6.74 2.135,6.938 0.156,0.198 10 false 9 1.927,6.531 2.24,6.729 0.313,0.198 10 false 3A 1.979,6.323 2.208,6.542 0.229,0.219 10 false 1 0.698,6.688 1.156,6.885 0.458,0.198 10 false ALT 0.458,7.083 1.531,7.281 1.073,0.198 10 false FL MAIN 0.656,7.667 1.729,7.865 1.073,0.198 10 false Battery 5.375,6.542 5.833,6.74 0.458,0.198 10 false G87 5.417,6.333 5.729,6.531 0.313,0.198 10 false 21 5.729,6.542 6.448,6.75 0.719,0.208 10 false IG1 1.844,7.573 4.552,7.802 2.708,0.229 10 false Instrument Panel Junction Block Assembly 5.333,7.844 7.063,8.094 1.729,0.25 10 false Engine Stop and Start ECU

A375261E01
0.083,0.073 2.156,0.313 2.073,0.24 12 false w/o Entry and Start System: 3.969,0.896 4.76,1.115 0.792,0.219 10 false BBC NO. 2 4.385,0.438 5.177,0.656 0.792,0.219 10 false BBC 4.677,0.177 4.833,0.375 0.156,0.198 10 false 2 4.083,0.625 4.24,0.823 0.156,0.198 10 false 1 4.49,0.625 4.646,0.823 0.156,0.198 10 false 2 4.25,0.188 4.406,0.385 0.156,0.198 10 false 1 5.365,0.281 5.823,0.479 0.458,0.198 10 false A86 5.448,0.104 5.604,0.302 0.156,0.198 10 false 3 5.729,0.292 6.344,0.49 0.615,0.198 10 false BIN1 5.74,0.729 6.354,0.927 0.615,0.198 10 false BIN2 5.438,0.552 5.594,0.75 0.156,0.198 10 false 1 5.375,0.729 5.833,0.927 0.458,0.198 10 false A86 5.729,1.458 6.188,1.656 0.458,0.198 10 false IG2 5.375,1.469 5.833,1.667 0.458,0.198 10 false G87 5.406,1.281 5.719,1.479 0.313,0.198 10 false 18 2,2.104 2.458,2.302 0.458,0.198 10 false IG2 1.156,1.635 1.615,1.833 0.458,0.198 10 false IG2 2.469,1.354 2.625,1.552 0.156,0.198 10 false 5 1.667,1.344 1.823,1.542 0.156,0.198 10 false 3 1.667,1.698 1.823,1.896 0.156,0.198 10 false 2 2.469,1.708 2.625,1.906 0.156,0.198 10 false 1 1.865,3.771 3.385,4.188 1.521,0.417 10 false Ignition or Starter Switch Assembly 1.844,3.583 2.156,3.781 0.313,0.198 10 false G4 3.021,3.219 3.479,3.417 0.458,0.198 10 false IG2 3.031,2.74 3.49,2.938 0.458,0.198 10 false IG1 2.969,2.5 3.427,2.698 0.458,0.198 10 false ACC 1.979,2.698 2.135,2.896 0.156,0.198 10 false 5 3.365,2.469 3.521,2.667 0.156,0.198 10 false 7 3.365,2.719 3.521,2.917 0.156,0.198 10 false 8 3.365,3.229 3.521,3.427 0.156,0.198 10 false 3 1.979,3.219 2.135,3.417 0.156,0.198 10 false 4 2.208,2.74 2.667,2.938 0.458,0.198 10 false AM1 2.208,3.219 2.667,3.417 0.458,0.198 10 false AM2 0.719,3.49 1.177,3.688 0.458,0.198 10 false AM2 1.75,4.969 2.208,5.167 0.458,0.198 10 false AM1 1.583,4.583 1.896,4.781 0.313,0.198 10 false 3C 1.469,4.365 1.781,4.563 0.313,0.198 10 false 48 3.615,4.583 3.927,4.781 0.313,0.198 10 false 3B 3.781,4.375 4.094,4.573 0.313,0.198 10 false 14 4.448,4.385 4.76,4.583 0.313,0.198 10 false 37 4.26,4.594 4.573,4.792 0.313,0.198 10 false 3C 3.927,5.063 4.385,5.26 0.458,0.198 10 false IGN 4.427,5.396 4.74,5.594 0.313,0.198 10 false 3D 4.427,5.208 4.74,5.406 0.313,0.198 10 false 50 3.74,5.542 4.198,5.74 0.458,0.198 10 false ACC 4.427,5.75 4.74,5.948 0.313,0.198 10 false 3C 4.427,5.573 4.74,5.771 0.313,0.198 10 false 45 2.958,6.021 3.417,6.219 0.458,0.198 10 false ACC 4.427,6.458 4.74,6.656 0.313,0.198 10 false 3D 4.438,6.271 4.75,6.469 0.313,0.198 10 false 43 4.417,6.823 4.729,7.021 0.313,0.198 10 false 3C 4.427,6.635 4.74,6.833 0.313,0.198 10 false 43 3.646,6.594 4.563,6.792 0.917,0.198 10 false EPS-IG 2.802,7.073 4.177,7.271 1.375,0.198 10 false IG1 NO. 1 0.688,6.615 1.146,6.813 0.458,0.198 10 false ALT 1.302,6.448 1.615,6.646 0.313,0.198 10 false 3A 1.333,6.25 1.49,6.448 0.156,0.198 10 false 1 1.302,6.823 1.615,7.021 0.313,0.198 10 false 3D 1.333,6.646 1.49,6.844 0.156,0.198 10 false 9 0.469,7.021 1.542,7.219 1.073,0.198 10 false FL MAIN 0.625,7.656 1.698,7.854 1.073,0.198 10 false Battery 1.417,7.479 4.198,7.719 2.781,0.24 10 false Instrument Panel Junction Block Assembly 5.719,6.448 6.521,6.698 0.802,0.25 10 false IG1 5.385,6.448 5.844,6.646 0.458,0.198 10 false G87 5.427,6.26 5.74,6.458 0.313,0.198 10 false 21 5.729,5.385 6.188,5.583 0.458,0.198 10 false ACC 5.385,5.396 5.844,5.594 0.458,0.198 10 false G87 5.417,5.208 5.729,5.406 0.313,0.198 10 false 19 5.313,7.833 7.083,8.042 1.771,0.208 10 false Engine Stop and Start ECU

A375262E01
0.5,0.698 3.521,0.938 3.021,0.24 10 false Main Body ECU (Multiplex Network Body ECU) 2.26,0.302 2.573,0.5 0.313,0.198 10 false IG 2.521,0.198 2.833,0.396 0.313,0.198 10 false 32 4.104,0.198 4.417,0.396 0.313,0.198 10 false 40 1.146,1.26 3.885,1.5 2.74,0.24 10 false Instrument Panel Junction Block Assembly 0.615,1.26 0.927,1.458 0.313,0.198 10 false 3D 0.198,1.573 1.167,1.781 0.969,0.208 10 false Q14*1, Q15*2 0.208,1.802 4.948,2 4.74,0.198 10 false Inner Rear View Mirror Assembly*3 3.563,1.854 3.875,2.052 0.313,0.198 10 false IG 3.854,1.74 4.156,1.938 0.302,0.198 10 false 1*1 0.26,2.688 0.719,2.885 0.458,0.198 10 false M30 0.271,2.948 3.01,3.146 2.74,0.198 10 false Tire Pressure Warning ECU and Receiver*4 2.292,2.5 2.604,2.698 0.313,0.198 10 false IG 2.583,2.396 2.802,2.604 0.219,0.208 10 false 1 0.646,4.094 2.146,4.292 1.5,0.198 10 false Network Gateway ECU 0.625,3.833 1.24,4.031 0.615,0.198 10 false G170 2.26,3.719 2.573,3.917 0.313,0.198 10 false IG1 2.573,3.583 2.792,3.792 0.219,0.208 10 false 11 5.677,3.74 6.292,3.938 0.615,0.198 10 false IG41 5.292,3.719 5.75,3.917 0.458,0.198 10 false G87 5.365,3.531 5.521,3.729 0.156,0.198 10 false 3 0.49,4.948 3.271,5.156 2.781,0.208 10 false Millimeter Wave Radar Sensor Assembly*5 2.229,4.615 2.688,4.813 0.458,0.198 10 false IGB 0.51,6.01 2.677,6.24 2.167,0.229 10 false Driving Support ECU Assembly*5 2.344,5.615 2.802,5.813 0.458,0.198 10 false B 4.833,6.698 7.063,6.906 2.229,0.208 10 false Lane Departure Warning Camera*2 4.406,8.323 4.563,8.521 0.156,0.198 10 false A 5.292,4.49 7.031,4.76 1.74,0.271 10 false Engine Stop and Start ECU 0.229,6.802 5.583,7 5.354,0.198 10 false *1: w/o Lane Departure Alert System 0.219,7.198 5.573,7.396 5.354,0.198 10 false *2: w/ Lane Departure Alert System 0.219,7.552 3.25,7.781 3.031,0.229 10 false *3: w/ EC Mirror 0.198,7.958 2.74,8.208 2.542,0.25 10 false *4: w/ Tire Pressure Warning System 0.188,8.344 3.229,8.594 3.042,0.25 10 false *5: w/ Dynamic Radar Cruise Control System 5.281,0.552 5.74,0.75 0.458,0.198 10 false A66 5.375,0.354 5.531,0.552 0.156,0.198 10 false 6 5.667,0.552 6.281,0.75 0.615,0.198 10 false DGND 5.667,1.479 6.281,1.677 0.615,0.198 10 false GND1 5.313,1.49 5.771,1.688 0.458,0.198 10 false A86 5.281,2.427 5.74,2.625 0.458,0.198 10 false A86 5.656,2.417 6.271,2.615 0.615,0.198 10 false GND2 5.365,2.24 5.521,2.438 0.156,0.198 10 false 2 5.365,1.281 5.521,1.479 0.156,0.198 10 false 8 0.49,4.76 0.802,4.958 0.313,0.198 10 false Z6 2.604,5.479 2.802,5.688 0.198,0.208 10 false 7 0.5,5.781 1.115,5.979 0.615,0.198 10 false G168 2.625,4.469 2.823,4.677 0.198,0.208 10 false 8 5.146,6.135 5.344,6.344 0.198,0.208 10 false 7 5.385,6.25 5.844,6.448 0.458,0.198 10 false IGB 4.823,6.5 5.281,6.698 0.458,0.198 10 false Q17 3.865,1.979 4.167,2.177 0.302,0.198 10 false 4*2

A375263E01
1.052,0.635 3.146,0.854 2.094,0.219 10 false Blind Spot Monitor Sensor LH*1 1.021,1.292 3.115,1.51 2.094,0.219 10 false Blind Spot Monitor Sensor RH*1 1.052,0.469 1.365,0.667 0.313,0.198 10 false R1 1.021,1.135 1.333,1.333 0.313,0.198 10 false T1 4.281,0.646 4.74,0.844 0.458,0.198 10 false BLB 4.635,1.365 4.854,1.552 0.219,0.188 10 false 5 4.271,1.271 4.729,1.469 0.458,0.198 10 false BRB 5.333,0.302 5.49,0.5 0.156,0.198 10 false A 1.115,2.198 2.625,2.448 1.51,0.25 10 false Parking Assist ECU*2 1.125,2 1.438,2.198 0.313,0.198 10 false a2 4.281,1.813 4.594,2.01 0.313,0.198 10 false IG 4.51,1.927 4.729,2.115 0.219,0.188 10 false 6 4.167,2.458 4.625,2.656 0.458,0.198 10 false ACC 4.51,2.563 4.667,2.76 0.156,0.198 10 false 1 4.271,2.146 4.583,2.344 0.313,0.198 10 false +B 4.51,2.26 4.667,2.458 0.156,0.198 10 false 2 1.052,3.448 2.969,3.688 1.917,0.24 10 false Combination Meter Assembly 1.073,3.302 1.531,3.5 0.458,0.198 10 false G16 3.865,3.448 4.125,3.698 0.26,0.25 10 false IG+ 4.156,3.573 4.469,3.771 0.313,0.198 10 false 39 3.698,4.208 4.26,4.406 0.563,0.198 10 false ACC1 3.823,4.656 4.135,4.854 0.313,0.198 10 false +B1 4.135,4.333 4.292,4.531 0.156,0.198 10 false 3 4.146,4.781 4.302,4.979 0.156,0.198 10 false 4 5.792,3.458 6.406,3.656 0.615,0.198 10 false IG12 5.417,3.458 5.875,3.656 0.458,0.198 10 false G87 5.469,3.271 5.781,3.469 0.313,0.198 10 false 10 5.802,4.208 6.417,4.406 0.615,0.198 10 false AC41 5.427,4.208 5.885,4.406 0.458,0.198 10 false G87 5.469,4.021 5.781,4.219 0.313,0.198 10 false 24 5.427,2.146 5.885,2.344 0.458,0.198 10 false G87 5.813,4.656 6.427,4.854 0.615,0.198 10 false B42 5.51,1.938 5.667,2.135 0.156,0.198 10 false 2 5.354,5.792 7.115,6.031 1.76,0.24 10 false Engine Stop and Start ECU 0.698,4.281 2.479,4.51 1.781,0.229 10 false Radio Receiver Assembly*3 0.656,4.656 2.698,4.865 2.042,0.208 10 false Navigation Receiver Assembly*4 0.615,5.042 3.156,5.25 2.542,0.208 10 false Radio and Display Receiver Assembly*5 0.688,4.104 1.146,4.302 0.458,0.198 10 false G46 0.646,4.5 1.104,4.698 0.458,0.198 10 false G137 0.615,4.906 1.073,5.104 0.458,0.198 10 false G141 0.396,6.531 5.292,6.729 4.896,0.198 10 false *1: w/ Blind Spot Monitor System 0.375,6.99 5.875,7.188 5.5,0.198 10 false *2: w/ Panoramic View Monitor System 0.375,7.438 4.5,7.635 4.125,0.198 10 false *3: for Radio Receiver Type 0.365,7.875 5.26,8.073 4.896,0.198 10 false *4: for Navigation Receiver Type 0.365,8.323 4.948,8.521 4.583,0.198 10 false *5: for Radio and Display Receiver Type 4.625,0.75 4.781,0.948 0.156,0.198 10 false 5 5.792,2.156 6.406,2.354 0.615,0.198 10 false B41 5.438,4.667 5.896,4.865 0.458,0.198 10 false G87 5.479,4.458 5.792,4.656 0.313,0.198 10 false 12

A375264E03
1.594,1.573 3.688,1.802 2.094,0.229 10 false Power Steering ECU Assembly 1.594,1.344 1.906,1.542 0.313,0.198 10 false h1 4.427,1.583 4.74,1.781 0.313,0.198 10 false IG 4.719,1.458 4.875,1.656 0.156,0.198 10 false 1 1.583,2.365 3.292,2.573 1.708,0.208 10 false Brake Actuator Assembly 1.583,2.188 2.042,2.385 0.458,0.198 10 false A80 4.365,2.344 4.677,2.542 0.313,0.198 10 false IG1 4.708,2.198 5.021,2.396 0.313,0.198 10 false 12 0.906,3.333 3.5,3.531 2.594,0.198 10 false Spiral with Sensor Cable Sub-assembly 0.906,3.115 1.365,3.313 0.458,0.198 10 false G12 4.438,3.333 4.75,3.531 0.313,0.198 10 false IG 4.74,3.219 4.896,3.417 0.156,0.198 10 false 4 5.302,4.125 7.083,4.333 1.781,0.208 10 false Engine Stop and Start ECU 5.438,2.323 5.896,2.521 0.458,0.198 10 false G87 5.5,2.094 5.656,2.292 0.156,0.198 10 false 1 5.427,1.594 5.885,1.792 0.458,0.198 10 false G87 5.51,1.375 5.667,1.573 0.156,0.198 10 false 6 5.813,1.583 6.427,1.781 0.615,0.198 10 false IG11 5.823,2.313 6.438,2.51 0.615,0.198 10 false IG31

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA

·

If electrical load from additional devices installed on the vehicle (aftermarket audio system, etc.) is applied to the BO1 or IGO1 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate. If the fuse function of the backup boost converter operates, any systems connected to the BO1 or IGO1 terminal in the engine stop and start ECU will not operate.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC, BBC NO. 2 FUSES)
a.

Disconnect the A86 engine stop and start ECU connector.


b.

Remove the BBC fuse from the engine room relay block and junction block assembly.


c.

Remove the BBC NO. 2 fuse from the engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-1 (BIN2) - BBC NO. 2 fuse terminal 2 Always Below 1 Ω
A86-3 (BIN1) - BBC fuse terminal 2 Always Below 1 Ω
A86-1 (BIN2) - Body ground Always 10 kΩ or higher
BBC NO. 2 fuse terminal 2 - Body ground Always 10 kΩ or higher
A86-3 (BIN1) - Body ground Always 10 kΩ or higher
BBC fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Disconnect the 3D instrument panel junction block assembly (main body ECU (multiplex network body ECU)) connector.


c.

w/ EC Mirror:

Disconnect the Q14*1 or Q15*2 inner rear view mirror assembly connector.

*1: w/o Lane Departure Alert System

*2: w/ Lane Departure Alert System



d.

w/ Tire Pressure Warning System:

Disconnect the M30 tire pressure warning ECU and receiver connector.


e.

Disconnect the G170 network gateway ECU connector.


f.

w/ Dynamic Radar Cruise Control System:

Disconnect the Z6 millimeter wave radar sensor assembly connector.


g.

w/ Dynamic Radar Cruise Control System:

Disconnect the G168 driving support ECU assembly connector.


h.

w/ Lane Departure Alert System:

Disconnect the Q17 lane departure warning camera connector.


i.

w/ Blind Spot Monitor System:

Disconnect the R1 blind spot monitor sensor LH connector.


j.

w/ Blind Spot Monitor System:

Disconnect the T1 blind spot monitor sensor RH connector.


k.

w/ Panoramic View Monitor System:

Disconnect the a2 parking assist ECU connector.


l.

for Radio Receiver Type:

Disconnect the G46 radio receiver assembly connector.


m.

for Navigation Receiver Type:

Disconnect the G137 navigation receiver assembly connector.


n.

for Radio and Display Receiver Type:

Disconnect the G141 radio and display receiver assembly connector.


o.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-3 (IG41) - 3D-40 (IG) Always Below 1 Ω
G87-3 (IG41) - Q14-1 (IG)*1, *10 Always Below 1 Ω
G87-3 (IG41) - Q15-4 (IG)*2, *10 Always Below 1 Ω
G87-3 (IG41) - M30-1 (IG)*3 Always Below 1 Ω
G87-3 (IG41) - G170-11 (IG1) Always Below 1 Ω
G87-3 (IG41) - Z6-8 (IGB)*4 Always Below 1 Ω
G87-3 (IG41) - G168-7 (IGB)*4 Always Below 1 Ω
G87-3 (IG41) - Q17-7 (IGB)*2 Always Below 1 Ω
G87-3 (IG41) - R1-5 (BLB)*5 Always Below 1 Ω
G87-3 (IG41) - T1-5 (BRB)*5 Always Below 1 Ω
G87-3 (IG41) - a2-6 (IG)*6 Always Below 1 Ω
G87-2 (B41) - a2-2 (+B)*6 Always Below 1 Ω
G87-12 (B42) - G46-4 (+B1)*7 Always Below 1 Ω
G87-12 (B42) - G137-4 (+B1)*8 Always Below 1 Ω
G87-12 (B42) - G141-4 (+B1)*9 Always Below 1 Ω
G87-3 (IG41) - Body ground Always 10 kΩ or higher
G87-12 (B42) - Body ground Always 10 kΩ or higher


·

*1: w/o Lane Departure Alert System

·

*2: w/ Lane Departure Alert System

·

*3: w/ Tire Pressure Warning System

·

*4: w/ Dynamic Radar Cruise Control System

·

*5: w/ Blind Spot Monitor System:

·

*6: w/ Panoramic View Monitor System

·

*7: for Radio Receiver Type

·

*8: for Navigation Receiver Type

·

*9: for Radio and Display Receiver Type

·

*10: w/ EC Mirror



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
A375785C01
1.51,0.135 1.938,0.427 0.427,0.292 3.156,0.125 3.583,0.417 0.427,0.292 4.948,0.125 5.375,0.417 0.427,0.292 5.51,1.948 5.938,2.24 0.427,0.292 3.188,1.969 3.615,2.26 0.427,0.292 1.094,2 1.521,2.292 0.427,0.292 1.594,0.198 1.969,0.396 0.375,0.198 10 false A86 3.25,0.188 3.625,0.385 0.375,0.198 10 false A66 5.031,0.188 5.406,0.385 0.375,0.198 10 false G87 1.167,2.063 1.542,2.26 0.375,0.198 10 false A86 3.25,2.031 3.625,2.229 0.375,0.198 10 false A66 5.583,2.021 5.958,2.219 0.375,0.198 10 false G87 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the A86, A66 and G87 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-3 (IG41) - A66-6 (DGND) Always 10 kΩ or higher
G87-2 (B41) - A66-6 (DGND) Always 10 kΩ or higher
G87-12 (B42) - A66-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK VEHICLE CONDITION (B41, IG41 CIRCUIT)

NG

4.CHECK VEHICLE CONDITION (B41, IG41 CIRCUIT)
a.

Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B41 or IG41 terminal circuit in the engine stop and start ECU.

Result:
Result Proceed to
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. A
Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. B




A

GO TO TROUBLE AREAS (TROUBLESHOOTING PROCEDURE FOR ECUS CONNECTED TO B41 AND IG41 TERMINALS)

B

END (REMOVE ELECTRICAL LOAD FROM ADDITIONAL DEVICE)