Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  P0335  Engine Speed Sensor Circuit (NE Circuit)  


DESCRIPTION

The crank position sensor sends an engine speed signal (NE signal) to the ECM. The engine speed signal is then sent directly from the NEO terminal of the ECM to the engine stop and start ECU. Additionally, the ECM sends the engine speed to the engine stop and start ECU via CAN communication. The engine stop and start ECU compares the NE signal and engine speed received via CAN communication to check for errors in the NE signal.

If the NE signal is abnormal, the engine stop and start ECU will blink the stop and start cancel indicator light and stores DTC P0335.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0335 Engine Speed Sensor Circuit (NE Circuit) All of the following conditions continue for 10 seconds (2 trip detection logic):
·

Normal communication between the ECM and the engine stop and start ECU.

·

Engine speed (NE signal) is below 6000 rpm.

·

Difference between the NE signal that is sent directly from ECM and the engine speed that is sent via CAN is 200 rpm or higher.


Both of the following conditions continue for 2 seconds or more (1 trip detection logic):
·

Starter is operating.

·

No NE signal input.


·

Wire harness or connector

·

Crankshaft position sensor

·

ECM

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and wait for at least 15 seconds.


e.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227
A199262E05
3.167,2.51 3.167,3.104 true 1.083,1.125 2.302,1.417 1.219,0.292 10 Engine Running 4.438,0.25 5.646,0.427 1.208,0.177 10 Judgment Timing 3.49,1.698 4.302,1.875 0.813,0.177 10 15 seconds 6.24,2.823 6.604,3 0.365,0.177 10 Time 1.083,2.406 2.167,2.635 1.083,0.229 10 Engine Stopped 2.813,3.135 3.833,3.375 1.021,0.24 10 Engine Started 4.031,3.323 6.229,3.531 2.198,0.208 10 Judged normal or abnormal



STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A354868E02
1.333,2.052 1.646,2.25 0.313,0.198 10 false NE 1.333,2.5 1.792,2.698 0.458,0.198 10 false NE- 1.333,2.969 1.646,3.167 0.313,0.198 10 false VG 2.74,2.052 3.198,2.25 0.458,0.198 10 false B112 2.729,2.521 3.188,2.719 0.458,0.198 10 false B112 2.729,3 3.188,3.198 0.458,0.198 10 false B112 3.167,2.052 3.625,2.25 0.458,0.198 10 false NE+ 3.167,2.521 3.479,2.719 0.313,0.198 10 false NE- 3.167,3 3.781,3.198 0.615,0.198 10 false VCNE 3.75,2.052 4.208,2.25 0.458,0.198 10 false NEO 3.74,2.521 4.354,2.719 0.615,0.198 10 false CANH 3.75,3 4.365,3.198 0.615,0.198 10 false CANL 4.281,2.042 4.74,2.24 0.458,0.198 10 false A62 4.281,2.521 4.74,2.719 0.458,0.198 10 false A62 4.281,3 4.74,3.198 0.458,0.198 10 false A62 5.833,0.406 6.146,0.604 0.313,0.198 10 false NE 5.469,2.042 5.927,2.24 0.458,0.198 10 false A66 5.469,2.521 6.083,2.719 0.615,0.198 10 false G87 5.469,3 6.083,3.198 0.615,0.198 10 false G87 5.469,3.469 5.927,3.667 0.458,0.198 10 false A66 5.417,0.802 6.031,1 0.615,0.198 10 false G82 5.417,1 6.958,1.406 1.542,0.406 10 false Certification ECU (Smart Key ECU Assembly)* 5.844,2.021 6.156,2.219 0.313,0.198 10 false NE 5.833,2.5 6.448,2.698 0.615,0.198 10 false CANH 5.833,2.99 6.448,3.188 0.615,0.198 10 false CANL 5.865,3.458 6.323,3.656 0.458,0.198 10 false DGND 5.323,3.99 7.156,4.156 1.833,0.167 10 false Engine Stop and Start ECU 3.448,3.448 3.906,3.646 0.458,0.198 10 false ECM 0.25,3.385 0.708,3.583 0.458,0.198 10 false B114 0.25,3.531 4.229,3.729 3.979,0.198 10 false Crankshaft Position Sensor 0.74,4.083 5.021,4.281 4.281,0.198 10 false *: w/ Entry and Start System 0.802,4.417 4.469,4.615 3.667,0.198 10 false : CAN Communication Line 1.75,1.917 1.906,2.115 0.156,0.198 10 false 2 1.75,2.417 1.906,2.615 0.156,0.198 10 false 3 1.75,2.885 1.906,3.083 0.156,0.198 10 false 1 2.75,1.854 3.208,2.052 0.458,0.198 10 false 121 2.792,2.344 3.104,2.542 0.313,0.198 10 false 90 2.75,2.813 3.208,3.01 0.458,0.198 10 false 122 4.365,1.833 4.521,2.031 0.156,0.198 10 false 6 4.333,2.323 4.646,2.521 0.313,0.198 10 false 26 4.333,2.802 4.646,3 0.313,0.198 10 false 25 5.5,1.844 5.813,2.042 0.313,0.198 10 false 10 5.51,2.313 5.823,2.51 0.313,0.198 10 false 15 5.5,2.802 5.813,3 0.313,0.198 10 false 16 5.542,3.281 5.698,3.479 0.156,0.198 10 false 6 5.583,0.333 5.781,0.531 0.198,0.198 10 false 16 4.76,1.104 4.917,1.302 0.156,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA


PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs

Powertrain > Engine and ECT > Trouble Codes
50001 371
Result:
Result Proceed to
No ECD system DTCs are output A
ECD system DTC is output B




A

2.READ VALUE USING GTS (ENGINE SPD (NE SIGNAL))

B

2.READ VALUE USING GTS (ENGINE SPD (NE SIGNAL))
a.

Connect the GTS to the DLC3


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Engine Spd (NE Signal).

Powertrain > Stop and Start > Data List
Tester Display
Engine Spd (NE Signal)
50003 227 4

e.

Read the value displayed on the GTS screen.

OK:

Engine speed signal is input (the speeds displayed on the tachometer and the GTS are almost the same).



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A62 ECM connector.


d.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-10 (NE) - A62-6 (NEO) Always Below 1 Ω
A66-10 (NE) - Body ground Always 10 kΩ or higher
A62-6 (NEO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-6 (DGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK ENGINE STOP AND START ECU (NE SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ENGINE STOP AND START ECU (NE SIGNAL INPUT)
A348175C98
3.229,0.146 3.604,0.385 0.375,0.24 2.021,0.146 2.396,0.385 0.375,0.24 4.656,0.135 5.031,0.375 0.375,0.24 2.74,1.396 2.906,0.823 true 3.865,1.417 3.677,0.823 true 0.208,0.094 0.521,0.292 0.313,0.198 10 false *a 3.302,0.198 3.615,0.396 0.313,0.198 10 false A66 2.094,0.198 2.406,0.396 0.313,0.198 10 false A86 4.719,0.177 5.031,0.375 0.313,0.198 10 false G87 2.646,1.448 2.958,1.646 0.313,0.198 10 false NE 3.792,1.448 4.208,1.646 0.417,0.198 10 false DGND
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Connect an oscilloscope to terminals A66-10 (NE) and A66-6 (DGND).


b.

Start the engine.


c.
A318633E04
2.792,1.042 3.25,1.24 0.458,0.198 10 false GND 0.26,0.073 1.49,0.271 1.229,0.198 10 false 5 V/DIV. 1.313,1.906 2.844,2.104 1.531,0.198 10 false 2 ms./DIV.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester Connection A66-10 (NE) - A66-6 (DGND)
Tool Setting 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

Result:
Result Proceed to
Pulse generation
(See waveform)
A
Stuck at 0 to 1.5 V B
Stuck at 8 to 14 V C




A

B

6.CHECK ENGINE STOP AND START ECU (NE TERMINAL VOLTAGE)

C

6.CHECK ENGINE STOP AND START ECU (NE TERMINAL VOLTAGE)
A348175C98
3.229,0.146 3.604,0.385 0.375,0.24 2.021,0.146 2.396,0.385 0.375,0.24 4.656,0.135 5.031,0.375 0.375,0.24 2.74,1.396 2.906,0.823 true 3.865,1.417 3.677,0.823 true 0.208,0.094 0.521,0.292 0.313,0.198 10 false *a 3.302,0.198 3.615,0.396 0.313,0.198 10 false A66 2.094,0.198 2.406,0.396 0.313,0.198 10 false A86 4.719,0.177 5.031,0.375 0.313,0.198 10 false G87 2.646,1.448 2.958,1.646 0.313,0.198 10 false NE 3.792,1.448 4.208,1.646 0.417,0.198 10 false DGND
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Disconnect the A62 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-10 (NE) - A66-6 (DGND) Ignition switch ON 8 to 14 V


HINT:

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.


Result:
Proceed to
OK
NG




OK

NG