Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

The engine stop and start ECU stores the number of starter assembly operations, air conditioning information, and the deceleration sensor zero point learning results.

If the engine stop and start ECU cannot write the number of starter assembly operations, air conditioning information, or the deceleration sensor zero point learning results, it stores DTC P062F, blinks the stop and start cancel indicator light, and prohibits stop and start control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P062F Internal Control Module EEPROM Error Any of the following conditions are met (1 trip detection logic):
·

Air conditioning information cannot be written

·

The deceleration sensor zero point learning value cannot be written

·

The number of starter operations was not successfully written to the EEPROM.


Engine stop and start ECU Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA


PROCEDURE

1.PERFORM REGISTRATION (ECU EXCHANGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility
Tester Display
ECU Exchange
50005 227 131

e.

According to the GTS display, download the previous status (the number of starter operations) from the engine stop and start ECU to the GTS.


Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


b.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 227

Result:
Proceed to
NEXT



NEXT

3.PERFORM REGISTRATION (STARTER EXCHANGE, RESET A/C INFORMATION, DECELERATION SENSOR ZERO POINT CLEAR)
3.PERFORM REGISTRATION (STARTER EXCHANGE, RESET A/C INFORMATION, DECELERATION SENSOR ZERO POINT CLEAR)
a.

Clear the number of starter operations.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Starter Exchange.

Powertrain > Stop and Start > Utility
Tester Display
Starter Exchange
50005 227 130


b.

Clear the air conditioning information.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Reset A/C Information.

Powertrain > Stop and Start > Utility
Tester Display
Reset A/C Information
50005 227 2104


c.

Clear the zero point calibration data of the deceleration sensor.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.

Powertrain > Stop and Start > Utility
Tester Display
Deceleration Sensor Zero Point Clear
50005 227 4174


Result:
Proceed to
NEXT



NEXT

4.PERFORM REGISTRATION (ECU EXCHANGE)
4.PERFORM REGISTRATION (ECU EXCHANGE)
a.

Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.

Powertrain > Stop and Start > Utility
Tester Display
ECU Exchange
50005 227 131

b.

According to the prompts on the GTS screen, write the information to the engine stop and start ECU.


c.

Perform air conditioning information learning.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

HINT:

When initialization of the air conditioning information is complete, air conditioning information learning is automatically performed.



d.

Perform deceleration sensor zero point calibration.

i.

Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.

Powertrain > Stop and Start > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 227 4147


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.


g.

Check for DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227

h.

Check the number of starter operations.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DATA LIST / ACTIVE TEST

Powertrain > Stop and Start > Data List
Tester Display
Starter Operation #
50003 227 56
Result:
Result Proceed to
DTC is not output A
DTC P062F is output B




A

END

B