Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  P1780  Discrepancy between Neutral Position SW and Shift Position  


DESCRIPTION

The engine stop and start ECU detects a malfunction by comparing the shift position signal with the neutral position sensor (neutral position switch) signal input state. When a malfunction occurs, the engine stop and start ECU stores this DTC, blinks the stop and start cancel indicator light, and prohibits the stop and start control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1780 Discrepancy between Neutral Position SW and Shift Position The following condition continues for 1 second or more (1 trip detection logic):
·

Open or short in neutral position sensor (neutral position switch) circuit.


·

Neutral position sensor (neutral position switch)

·

Engine stop and start ECU

·

Wire harness or connector


Blinks DTC stored

WIRING DIAGRAM

A285528E26
2.167,0.729 2.688,0.958 0.521,0.229 10 false W1 2.177,1.198 2.635,1.427 0.458,0.229 10 false F+ 2.073,1.646 2.521,1.958 0.448,0.313 10 false TMN 0.635,2.073 1.083,2.292 0.448,0.219 10 false C16 0.625,2.281 3.729,2.563 3.104,0.281 10 false Neutral Position Sensor (Neutral Position Switch) 2.469,0.635 3.031,0.938 0.563,0.302 10 false 1 2.469,1.094 2.802,1.365 0.333,0.271 10 false 3 2.469,1.552 2.833,1.823 0.365,0.271 10 false 2 4.49,0.625 4.969,0.906 0.479,0.281 10 false 26 4.49,1.073 4.833,1.313 0.344,0.24 10 false 25 4.5,1.552 4.802,1.792 0.302,0.24 10 false 8 4.75,0.729 5.344,1.01 0.594,0.281 10 false TMVC 4.75,1.188 5.188,1.417 0.438,0.229 10 false TME2 4.75,1.656 5.333,2.021 0.583,0.365 10 false TMN 4.594,2.125 4.875,2.333 0.281,0.208 10 false A66 4.583,2.281 6.573,2.5 1.99,0.219 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9

e.

Read the value when the shift lever is in neutral and any other position

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in neutral ON
Shift lever in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the C16 neutral position sensor (neutral position switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-26 (TMVC) - C16-1 (W1) Always Below 1 Ω
A66-25 (TME2) - C16-3 (F+) Always Below 1 Ω
A66-8 (TMN) - C16-2 (TMN) Always Below 1 Ω
A66-26 (TMVC) - Body ground Always 10 kΩ or higher
C16-1 (W1) - Body ground Always 10 kΩ or higher
A66-25 (TME2) - Body ground Always 10 kΩ or higher
C16-3 (F+) - Body ground Always 10 kΩ or higher
A66-8 (TMN) - Body ground Always 10 kΩ or higher
C16-2 (TMN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
A346331C72
3.188,0.615 3.708,0.844 0.521,0.229 2.521,0.583 2.771,0.583 2.771,0.583 3.104,1.167 true 3.115,1.333 3.198,2.198 true 3.313,0.646 3.771,0.844 0.458,0.198 10 false A73 3.021,2.24 3.521,2.438 0.5,0.198 10 false TME2 2.083,0.5 2.5,0.75 0.417,0.25 10 false TMN 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-8 (TMN) - A66-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Proceed to
OK
NG



OK

NG