Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) J

STOP AND START  STOP AND START SYSTEM(for 2WW)  Neutral Position Switch Circuit  


DESCRIPTION

The neutral position sensor (neutral position switch) detects whether the shift lever is in neutral. When the shift lever in any position other than neutral, stop and start control is prohibited

PROCEDURE

1.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9

e.

Read the value when the shift lever is in neutral and any other position

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever is in neutral ON
Shift lever is in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the C16 neutral position sensor (neutral position switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-26 (TMVC) - C16-1 (W1) Always Below 1 Ω
A66-25 (TME2) - C16-3 (F+) Always Below 1 Ω
A66-8 (TMN) - C16-2 (TMN) Always Below 1 Ω
A66-26 (TMVC) - Body ground Always 10 kΩ or higher
C16-1 (W1) - Body ground Always 10 kΩ or higher
A66-25 (TME2) - Body ground Always 10 kΩ or higher
C16-3 (F+) - Body ground Always 10 kΩ or higher
A66-8 (TMN) - Body ground Always 10 kΩ or higher
C16-2 (TMN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
A346331C72
3.188,0.615 3.708,0.844 0.521,0.229 2.521,0.583 2.771,0.583 2.771,0.583 3.104,1.167 true 3.115,1.333 3.198,2.198 true 3.313,0.646 3.771,0.844 0.458,0.198 10 false A73 3.021,2.24 3.521,2.438 0.5,0.198 10 false TME2 2.083,0.5 2.5,0.75 0.417,0.25 10 false TMN 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-8 (TMN) - A66-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG