Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 2WW) › from 2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0208733 STOP AND START SYSTEM(for 2WW) C

STOP AND START  STOP AND START SYSTEM(for 2WW)  P1862  Clutch Control System 2  


DESCRIPTION

There are 2 clutch pedal switches for the clutch pedal. The clutch switch assembly (for upper) is used for stopping and restarting of the engine by stop and start control. During the stop and start control, the clutch start switch assembly (for lower) is used only when the clutch switch assembly (for upper) is stuck on or the fail-safe function is activated.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1862 Clutch Control System 2 Both of the following conditions continue for 0.5 seconds or more (1 trip detection logic):
·

Clutch start switch assembly (for lower) is on.

·

Clutch switch assembly (for upper) is on.


·

Clutch start switch assembly (for lower)

·

Clutch switch assembly (for upper)

·

Wire harness or connector

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine.


e.
A206932E04
1.302,1.948 1.302,2.708 false 1.594,1.948 1.594,2.708 false 1.323,2.167 1.865,2.167 false 1.365,2.208 1.323,2.167 1.323,2.167 1.365,2.135 false 1.823,2.135 1.865,2.167 1.865,2.167 1.823,2.208 false 1.708,2.167 1.958,2.74 false 1.469,2.167 1.208,2.74 false 1.542,2.135 1.594,2.167 1.594,2.167 1.542,2.208 false 1.635,2.208 1.594,2.167 1.594,2.167 1.635,2.135 false 1.875,1.927 1.875,2.708 false 0.135,0.115 1.458,0.302 1.323,0.188 10 Clutch Switch Signal 1.99,2.719 3.135,2.906 1.146,0.188 10 1 second or more 0.281,2.719 1.052,3.031 0.771,0.313 10 1 second or more 0.583,1.177 0.833,1.333 0.25,0.156 10 ON 0.583,1.854 0.896,2.01 0.313,0.156 10 OFF

Fully depress the clutch pedal for 1 second or more. Release the clutch pedal and wait for at least 1 second.


f.

Repeat the previous step 3 times.


g.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A299444E04
6.021,0.5 6.479,0.698 0.458,0.198 10 false CLU 5.667,0.5 6.125,0.698 0.458,0.198 10 false A66 5.688,0.302 6,0.5 0.313,0.198 10 false 11 5.656,4.531 6.115,4.729 0.458,0.198 10 false A66 5.656,1.469 6.115,1.667 0.458,0.198 10 false A66 6.042,1.469 6.354,1.667 0.313,0.198 10 false +B 5.729,1.271 5.885,1.469 0.156,0.198 10 false 1 6.031,4.531 6.49,4.729 0.458,0.198 10 false CLL 5.688,4.333 6,4.531 0.313,0.198 10 false 17 5.667,6.323 6.125,6.521 0.458,0.198 10 false A66 5.656,7.083 6.115,7.281 0.458,0.198 10 false A66 6.01,6.313 6.469,6.51 0.458,0.198 10 false STA 5.698,6.115 6.01,6.313 0.313,0.198 10 false 21 6,7.083 6.458,7.281 0.458,0.198 10 false DGND 5.74,6.865 5.896,7.063 0.156,0.198 10 false 6 3.385,0.979 5.99,1.167 2.604,0.188 10 false Clutch Switch Assembly (for Upper) 3.396,0.823 4.927,1.021 1.531,0.198 10 false A1*1, F1*2 4.833,0.396 5.021,0.563 0.188,0.167 10 false 2 3.563,0.375 3.719,0.573 0.156,0.198 10 false 1 2.417,1.615 3.792,1.813 1.375,0.198 10 false EFI NO. 1 1.844,1.354 2,1.552 0.156,0.198 10 false 3 1.844,1.646 2.031,1.813 0.188,0.167 10 false 2 1.083,1.646 1.24,1.844 0.156,0.198 10 false 1 1.104,1.344 1.26,1.542 0.156,0.198 10 false 5 0.656,0.802 2.073,1.031 1.417,0.229 10 false EFI-MAIN NO. 1 1,2.125 2.417,2.354 1.417,0.229 10 false EFI-MAIN NO. 1 2.167,3.365 2.625,3.563 0.458,0.198 10 false A62 2.26,3.156 2.573,3.354 0.313,0.198 10 false 9 3.969,2.385 4.281,2.583 0.313,0.198 10 false 36 3.948,2.594 4.406,2.792 0.458,0.198 10 false A62 3.531,2.594 3.99,2.792 0.458,0.198 10 false STA 2.531,3.354 3.146,3.552 0.615,0.198 10 false MREL 2.927,3.75 3.385,3.948 0.458,0.198 10 false ECM 1.01,5.052 3.375,5.323 2.365,0.271 10 false Ignition or Starter Switch Assembly 0.99,4.885 1.302,5.083 0.313,0.198 10 false G4 2.688,4.385 2.875,4.552 0.188,0.167 10 false 2 2.292,4.438 2.75,4.635 0.458,0.198 10 false ST2 1.229,4.438 1.688,4.635 0.458,0.198 10 false AM2 1.052,4.417 1.208,4.615 0.156,0.198 10 false 4 0.615,4.688 1.073,4.885 0.458,0.198 10 false AM2 3.688,5.052 3.875,5.219 0.188,0.167 10 false 2 3.667,5.885 3.823,6.083 0.156,0.198 10 false 1 3.885,5.406 5.198,5.823 1.313,0.417 10 false Clutch Start Switch Assembly (for Lower) 3.896,5.229 5.427,5.427 1.531,0.198 10 false A4*1, F2*2 1.896,6.646 2.354,6.844 0.458,0.198 10 false ST 1.302,5.677 1.76,5.875 0.458,0.198 10 false ST 2.323,5.896 2.479,6.094 0.156,0.198 10 false 5 1.583,5.896 1.74,6.094 0.156,0.198 10 false 3 2.323,6.208 2.51,6.375 0.188,0.167 10 false 2 1.573,6.219 1.729,6.417 0.156,0.198 10 false 1 2.563,6.875 2.875,7.073 0.313,0.198 10 false B6 2.604,6.656 2.76,6.854 0.156,0.198 10 false 1 2.594,7.115 2.75,7.313 0.156,0.198 10 false 1 2.573,7.323 2.885,7.521 0.313,0.198 10 false C4 5.365,7.698 7.094,8.094 1.729,0.396 10 false Engine Stop and Start ECU 3.021,7.948 4.25,8.188 1.229,0.24 10 false Starter Assembly 0.552,7.677 1.625,7.875 1.073,0.198 10 false Battery 0.667,8.104 2.354,8.302 1.688,0.198 10 false *1: for LHD 0.667,8.427 2.354,8.625 1.688,0.198 10 false *2: for RHD 0.052,0.052 5.01,0.292 4.958,0.24 12 false w/o Entry and Start System: 0.385,6.313 1.458,6.51 1.073,0.198 10 false FL MAIN

A299445E03
5.656,0.625 6.115,0.823 0.458,0.198 10 false A66 6.031,0.615 6.49,0.813 0.458,0.198 10 false CLU 5.698,0.427 6.01,0.625 0.313,0.198 10 false 11 5.667,1.469 6.125,1.667 0.458,0.198 10 false A66 5.667,7.083 6.125,7.281 0.458,0.198 10 false A66 6.021,1.458 6.333,1.656 0.313,0.198 10 false +B 6.021,7.104 6.479,7.302 0.458,0.198 10 false DGND 5.75,6.896 5.906,7.094 0.156,0.198 10 false 6 5.656,4.052 6.115,4.25 0.458,0.198 10 false A66 5.656,6.323 6.115,6.521 0.458,0.198 10 false A66 6.021,4.063 6.479,4.26 0.458,0.198 10 false CLL 6.031,6.333 6.49,6.531 0.458,0.198 10 false STA 5.75,1.271 5.906,1.448 0.156,0.177 10 false 1 5.698,3.844 6.01,4.042 0.313,0.198 10 false 17 5.698,6.125 6.01,6.323 0.313,0.198 10 false 21 3.479,0.958 4.333,1.167 0.854,0.208 10 false A1*1, F1*2 3.458,1.115 6.021,1.385 2.563,0.271 10 false Clutch Switch Assembly (for Upper) 5.094,0.521 5.25,0.719 0.156,0.198 10 false 2 3.844,0.5 4,0.698 0.156,0.198 10 false 1 2.406,1.615 3.125,1.823 0.719,0.208 10 false EFI NO. 1 1.052,1.354 1.208,1.531 0.156,0.177 10 false 5 1.813,1.365 1.969,1.563 0.156,0.198 10 false 3 1.813,1.646 1.969,1.844 0.156,0.198 10 false 2 1.042,1.656 1.208,1.854 0.167,0.198 10 false 1 0.604,0.813 1.844,1.01 1.24,0.198 10 false EFI-MAIN NO. 1 0.927,2.135 2.167,2.333 1.24,0.198 10 false EFI-MAIN NO. 1 2.531,3.146 3.146,3.344 0.615,0.198 10 false MREL 3.531,2.594 3.99,2.792 0.458,0.198 10 false STA 3.958,2.594 4.417,2.792 0.458,0.198 10 false A62 4,2.396 4.313,2.594 0.313,0.198 10 false 36 2.167,3.125 2.625,3.323 0.458,0.198 10 false A62 2.26,2.917 2.573,3.115 0.313,0.198 10 false 9 2.969,3.75 3.427,3.948 0.458,0.198 10 false ECM 0.969,4.875 3.094,5.24 2.125,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.969,4.719 1.427,4.917 0.458,0.198 10 false G82 1.281,4.208 1.594,4.406 0.313,0.198 10 false +B 1.104,4.094 1.26,4.292 0.156,0.198 10 false 2 1.833,4.052 2.448,4.25 0.615,0.198 10 false STAR 2.292,3.927 2.448,4.104 0.156,0.177 10 false 5 1.927,4.385 2.385,4.583 0.458,0.198 10 false STA 2.292,4.271 2.448,4.469 0.156,0.198 10 false 7 0.667,4.365 1.125,4.563 0.458,0.198 10 false AM2 4.021,4.792 5.552,4.99 1.531,0.198 10 false A4*1, F2*2 4.01,4.99 5.302,5.458 1.292,0.469 10 false Clutch Start Switch Assembly (for Lower) 3.656,4.771 3.813,4.969 0.156,0.198 10 false 2 3.656,5.563 3.823,5.76 0.167,0.198 10 false 1 0.583,5.781 0.896,5.979 0.313,0.198 10 false ST 1.875,6.656 2.188,6.854 0.313,0.198 10 false ST 2.365,5.896 2.521,6.073 0.156,0.177 10 false 5 1.552,5.896 1.708,6.094 0.156,0.198 10 false 3 2.365,6.208 2.521,6.406 0.156,0.198 10 false 2 1.552,6.208 1.719,6.406 0.167,0.198 10 false 1 2.573,6.865 2.885,7.063 0.313,0.198 10 false B6 2.594,6.646 2.76,6.844 0.167,0.198 10 false 1 2.594,7.135 2.76,7.333 0.167,0.198 10 false 1 2.563,7.333 2.875,7.531 0.313,0.198 10 false C4 3.083,7.948 4.26,8.146 1.177,0.198 10 false Starter Assembly 0.573,7.646 1.646,7.844 1.073,0.198 10 false Battery 0.948,8.073 2.635,8.271 1.688,0.198 10 false *1: for LHD 0.948,8.406 2.635,8.604 1.688,0.198 10 false *2: for RHD 0.063,0.052 4.833,0.292 4.771,0.24 12 false w/ Entry and Start System: 0.396,6.313 1.469,6.51 1.073,0.198 10 false FL MAIN 5.333,7.729 7.083,8.052 1.75,0.323 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 2WW)>REGISTRATION



PROCEDURE

1.READ VALUE USING GTS (CLUTCH UPPER SW AND CLUTCH LOWER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Upper SW and Clutch Lower SW.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Upper SW
Clutch Lower SW
50003 227 10,11

e.

Depress the clutch pedal and read the values displayed on the GTS.

OK:
Tester Display Condition Normal Condition
Clutch Upper SW Fully Depressed OFF
Clutch Lower SW Fully Depressed ON
Clutch Upper SW Fully Released ON
Clutch Lower SW Fully Released OFF



Result:
Proceed to
NG
OK



NG

2.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

OK

2.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
a.

Inspect the clutch start switch assembly (for lower).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT CLUTCH SWITCH ASSEMBLY (FOR UPPER)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

3.INSPECT CLUTCH SWITCH ASSEMBLY (FOR UPPER)
a.

Inspect the clutch switch assembly (for upper).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))

NG

REPLACE CLUTCH SWITCH ASSEMBLY (FOR UPPER)

4.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.

*1: for LHD

*2: for RHD



c.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


d.

w/o Entry and Start System:

Disconnect the G4 ignition or starter switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A66-17 (CLL) - A4-2 Always Below 1 Ω
A66-17 (CLL) - Body ground Always 10 kΩ or higher
A4-2 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A66-17 (CLL) - F2-2 Always Below 1 Ω
A66-17 (CLL) - Body ground Always 10 kΩ or higher
F2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH SWITCH ASSEMBLY (FOR UPPER))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH SWITCH ASSEMBLY (FOR UPPER))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A1*1 or F1*2 clutch switch assembly (for upper) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A66-11 (CLU) - A1-2 Always Below 1 Ω
A66-11 (CLU) - Body ground Always 10 kΩ or higher
A1-2 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A66-11 (CLU) - F1-2 Always Below 1 Ω
A66-11 (CLU) - Body ground Always 10 kΩ or higher
F1-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR