Home › Engine / Hybrid System › 2WW EMISSION CONTROL › EXHAUST GAS TEMPERATURE SENSOR(for Sensor 1) › from 2015.10
RM3090E _51 Engine / Hybrid System _044375 2WW EMISSION CONTROL _0210865 EXHAUST GAS TEMPERATURE SENSOR(for Sensor 1) A

2WW EMISSION CONTROL  EXHAUST GAS TEMPERATURE SENSOR(for Sensor 1)  INSTALLATION  


PROCEDURE

Hide 89425 1.INSTALL EXHAUST GAS TEMPERATURE SENSOR (for Sensor 1)

a.
A359381C01
1.625,2.938 2.021,3.188 0.396,0.25 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the exhaust gas temperature sensor.

Torque:
Specified tightening torque : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

If the exhaust gas temperature sensor is dropped, replace it with a new one.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 300 mm (11.8 in.)): 28 N*m (286 kgf*cm, 21 ft.*lbf)




Hide 17271 2.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator with the 3 bolts and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 3.CONNECT VACUUM CONTROL VALVE BRACKET

a.

Using a T20 "TORX" socket wrench, connect the vacuum control valve bracket with the 3 screws.


b.

Attach the air fuel ratio sensor clamp to the vacuum control valve bracket.


c.
A341655C01
0.979,3.521 1.115,3.521 1.115,3.521 1.24,3.833 false 1.948,3.583 1.802,3.583 1.802,3.583 1.76,3.938 false 2.604,3.479 2.458,3.479 2.458,3.479 2.417,3.833 false 1.063,2.031 1.271,2.104 1.271,2.104 1.271,2.25 false 3.052,1.594 2.906,1.594 2.906,1.594 2.698,1.75 true 2.698,1.323 2.552,1.323 2.552,1.323 2.344,1.479 true 0.781,3.438 1.094,3.646 0.313,0.208 10 false *1 3.042,3.833 3.292,4.063 0.25,0.229 10 false *a 1.219,2.281 1.479,2.479 0.26,0.198 10 false *b 3.104,1.51 3.333,1.708 0.229,0.198 10 true *c 2.021,3.5 2.302,3.698 0.281,0.198 10 false *d 2.656,3.406 2.938,3.604 0.281,0.198 10 false *d 2.75,1.24 3,1.458 0.25,0.219 10 true *b
*1 Vacuum Control Valve Bracket
*a 1.5 mm (0.0591 in.) or less
*b Air Fuel Ratio Sensor Connector Wire
*c Exhaust Gas Temperature Sensor Connector Wire
*d Air Fuel Ratio Sensor Connector


Move the clamp as shown in the illustration, and secure the air fuel ratio sensor and exhaust gas temperature sensor with the clamp.

NOTICE:

The wire harness may become damaged if not installed when the clamp is open.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 300 mm (11.8 in.)): 28 N*m (286 kgf*cm, 21 ft.*lbf)




d.

Lower the air fuel ratio sensor connector to the position shown in the illustration.


e.

Connect the air fuel ratio sensor connector.


f.

Connect the exhaust gas temperature sensor connector.


g.

Attach the wire harness clamp.


h.

Connect the exhaust gas temperature sensor connector.