Home › Engine / Hybrid System › 2WW ENGINE MECHANICAL › ENGINE ASSEMBLY › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _044373 2WW ENGINE MECHANICAL _0211288 ENGINE ASSEMBLY A

2WW ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle assembly is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Install the engine mounting insulator LH to the vehicle body with the 4 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12361A 2.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Temporarily install the front engine mounting insulator with the bolt and nut.


Hide 12371A 3.TEMPORARILY INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Temporarily install the rear engine mounting insulator with the bolt.


Hide 4.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install a sling device and chain block to the engine assembly and hang the engine assembly.


b.

Remove the engine assembly from the engine stand.


Hide 30300 5.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C341146

Make sure that the dowel pins are not loose, bent, damaged or scratched.


b.

Align the input shaft with the clutch disc assembly and install the engine assembly to the transaxle.


c.
C341143

Temporarily install the engine assembly with the 6 bolts.

NOTICE:
·

Be extremely careful that the vehicle body, clutch pipe line and radiator cooling fan do not interfere with the manual transaxle assembly when installing the manual transaxle assembly.

·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.

·

Before tightening the bolts, insert the dowel pins into the dowel holes securely so that the end face of the transaxle assembly fits close against the engine assembly.

·

Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.

·

Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.




Hide 17119 6.TEMPORARILY INSTALL NO. 2 MANIFOLD STAY

Hide 8.TIGHTEN ENGINE AND TRANSAXLE CONNECTING BOLT

Hide 9.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the manual transaxle assembly with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 10.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket to the manual transaxle assembly with the 5 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 11.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket LH to the manual transaxle assembly with the 5 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 17360E 13.INSTALL NO. 1 AIR TUBE ASSEMBLY

a.

Install the No. 1 air tube assembly to the manual transaxle assembly with the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Connect the No. 4 water by-pass hose to the EGR cooler assembly.


c.

Connect the compressor outlet elbow to the turbocharger sub-assembly.


Hide 82121 14.INSTALL ENGINE WIRE

a.

Connect the connectors, attach the clamps and install the engine wire to the engine assembly with the bracket bolts.


Hide 15.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on the engine lifter.

NOTICE:

Place height adjustment attachments and plate lift attachments under the engine assembly with transaxle.



b.

Operate the engine lifter and lift the engine assembly with transaxle to the position where the engine mounting insulator LH and engine mounting insulator sub-assembly RH can be installed.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.



c.

Install the engine mounting insulator LH with the bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

HINT:

When tightening the through bolt, keep the nut from rotating.



d.
A372599E01
1.281,1.792 1.438,1.99 0.156,0.198 10 true B 2.417,1.719 2.573,1.917 0.156,0.198 10 true A 0.552,1.083 0.708,1.281 0.156,0.198 10 true A

Install the engine mounting insulator sub-assembly RH with the 4 bolts and 3 nuts.

Torque:
Bolt and nut (A) : 95 N*m (969 kgf*cm, 70 ft.*lbf)
Nut (B) : 52 N*m (530 kgf*cm, 38 ft.*lbf)


e.

Attach the 2 clamps and connect the suction pipe sub-assembly.


f.

Attach the 2 clamps and connect the air conditioner tube and accessory assembly.


g.

Install the front crossmember sub-assembly with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


h.

Connect the front engine mounting insulator to the front crossmember sub-assembly with the 2 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 51201 16.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 52258A 17.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257 18.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Perform the same procedure as for the LH side.


Hide 51218A 19.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the front suspension member reinforcement LH to the front suspension crossmember sub-assembly with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51217A 20.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.

Install the front suspension member reinforcement RH to the front suspension crossmember sub-assembly with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51425A 21.INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT

a.

Install the front engine mounting bracket lower reinforcement to the front suspension crossmember sub-assembly with the 2 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 12371A 22.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Fully install the rear engine mounting insulator with the bolt.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12361A 23.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Fully install the front engine mounting insulator with the nut and bolt.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

HINT:

Tighten the through bolt while holding the nut.



Hide 45025D 25.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 26.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 27.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 31470 28.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 33820B 29.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transaxle control cable assembly to the control cable bracket with 2 new clips.

NOTICE:

Do not bend the transaxle control cable assembly more than necessary.



b.

Connect the transaxle control cable assembly to the manual transaxle assembly and install the 2 clips.

HINT:

Make sure that the metal washer plate of the shift cable is facing toward the outside of the vehicle.



Hide 17771A 30.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket with the 3 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 28610 31.INSTALL GLOW PLUG RELAY ASSEMBLY

a.

Connect the glow plug relay assembly to the ECM bracket.


Hide 23921 32.INSTALL FUEL FILTER SUPPORT

a.

Install the nut with fuel filter support stay.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


b.
A372609E01
1.75,1.948 1.906,2.146 0.156,0.198 10 true A 0.76,1.979 0.917,2.177 0.156,0.198 10 true A 3.094,0.927 3.25,1.125 0.156,0.198 10 true B

Install the fuel filter support with the 3 bolts.

Torque:
for bolt A : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)
for bolt B : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.

Attach the clamp to connect the wire harness.


d.

Attach the 4 clamps and connect the engine wire.


e.

Connect the connector.


f.
A372607

Connect the ECM connector and lower the lever.

NOTICE:
·

When connecting the ECM connector, make sure that dirt, water or other foreign matter is not stuck between the ECM connector and ECM.

·

Make sure that the lever is securely locked.




Hide 23300 33.INSTALL FUEL FILTER ASSEMBLY

Hide 34.CONNECT ENGINE WIRE

a.

Connect the ground cable with the bolt.

Torque:
8.35 N*m (85 kgf*cm, 74 in.*lbf)


b.

Connect the 2 connectors and engine wire, attach the 2 claws to the No. 1 engine room relay block and install the 2 nuts.

Torque:
8.35 N*m (85 kgf*cm, 74 in.*lbf)


c.

Install the No. 1 engine room relay block cover.


Hide 87246A 35.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the No. 1 air tube assembly, and slide the clamp to secure the hose.


Hide 36.CONNECT WATER HOSE SUB-ASSEMBLY

a.

Connect the water hose sub-assembly to the No. 1 air tube assembly, and slide the clamp to secure the hose.


Hide 23271H 37.CONNECT FUEL HOSE

a.

Connect the fuel hose to the fuel feed pipe sub-assembly.


Hide 23273H 38.CONNECT NO. 2 FUEL HOSE

a.

Connect the No. 2 fuel hose to the fuel feed pipe sub-assembly.


Hide 44777 39.CONNECT VACUUM HOSE

a.

Connect the vacuum hose to the No. 2 vacuum hose assembly, and slide the clamp to secure the hose.


Hide 40.INSTALL RADIATOR HOSE SUB-ASSEMBLY

a.

Install the radiator hose sub-assembly to the water outlet.


b.

Connect the radiator hose sub-assembly, and slide the clamp to secure the hose.


Hide 16261 41.INSTALL WATER BY-PASS HOSE ASSEMBLY

a.

Install the water by-pass hose assembly to the water by-pass pipe.


b.

Connect the water by-pass hose assembly to the No. 1 air tube assembly, and slide the clamp to secure the hose.


Hide 16470 42.INSTALL RADIATOR RESERVOIR ASSEMBLY

a.

Install the radiator reservoir assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the No. 2 water by-pass hose assembly to the radiator reservoir assembly, and slide the clamp to secure the hose.


c.

Connect the water by-pass hose assembly to the radiator reservoir assembly, and slide the clamp to secure the hose.


Hide 17880 44.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY

Hide 88703 45.CONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 88704 46.CONNECT SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 16400 47.INSTALL RADIATOR ASSEMBLY

Hide 74414B 48.INSTALL BATTERY BRACKET REINFORCEMENT

Hide 74431 50.INSTALL BATTERY TRAY

Hide 28800 51.INSTALL BATTERY

Hide 28899 52.INSTALL BATTERY INSULATOR

Hide 17410 54.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 59.CHARGE REFRIGERANT (w/ Air Conditioning System)

Hide 61.INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)

Hide 51443 66.INSTALL REAR ENGINE UNDER COVER RH

Hide 51444 67.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH with the 2 clips.


Hide 58165C 68.INSTALL FRONT FLOOR COVER RH

a.

Install the front floor cover RH with the 3 nuts and 3 clips.


Hide 51442 69.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the bolt and clip.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 50819 70.INSTALL FRONT FLOOR COVER

Hide 12611 71.INSTALL NO. 1 ENGINE COVER

a.
A372601C01
2.521,1.729 2.427,1.229 true 1.542,0.615 1.01,0.49 true 1.146,1.021 1.01,0.49 true 2.51,1.74 1.927,1.625 true 0.917,0.323 1.229,0.479 0.313,0.156 10 true *a 2.573,1.708 2.885,1.865 0.313,0.156 10 true *a
*a Installation Points


Attach the 4 clips in the sequence shown in the illustration to install the No. 1 engine cover.

HINT:

When attaching the clips, press the protrusions on the top of the No. 1 engine cover at the clip installation points.



Hide 52618 72.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Install the 2 hooks of the front lower bumper absorber into the installation holes in the body to install the front lower bumper absorber.


b.

Install the front lower bumper absorber with the 4 bolts.


Hide 76.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51441 78.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 10 clips.


b.

Install the 4 bolts and 2 screws.