1. DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.DRAIN FUEL
5.DISCONNECT PARKING BRAKE CABLE
Remove the 2 bolts and disconnect the parking brake cable.
50819
6.REMOVE FRONT FLOOR COVER (w/ COVER)
Remove the bolt and nut.
Detach the 5 clips and remove the front floor cover.
77641A
7.REMOVE NO. 1 FUEL TANK PROTECTOR (w/ COVER)
Detach the 3 clips and remove the nut and No. 1 fuel tank protector.
77641A
8.REMOVE NO. 1 FUEL TANK PROTECTOR (w/o COVER)
Remove the 2 clips and grommet.
Remove the 2 bolts and fuel tank protector.
58398F
9.REMOVE NO. 1 FLOOR UNDER COVER (w/ COVER)
Detach the clip and remove the 2 nuts and No. 1 floor under cover.
77026A
10.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Slide the clamp and disconnect the No. 1 fuel evaporation tube sub-assembly.
77209D
11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly.
Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION
77276
12.REMOVE FUEL HOSE PROTECTOR
Detach the claw and remove the fuel hose protector from the fuel tank to filler pipe hose.
77213E
13.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
77707
14.DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY
Detach the hose clamp.
Slide the clamp and disconnect the charcoal canister outlet tube sub-assembly from the fuel tank breather tube.
77014A
15.DISCONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
Disconnect the No. 3 fuel breather tube sub-assembly from the fuel tank assembly.
Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION
77100
16.REMOVE FUEL TANK ASSEMBLY
Detach the 3 wire harness clamps.
Using an engine lifter and attachments, support the fuel tank assembly.
Remove the 2 bolts and No. 1 fuel tank band sub-assembly.
Remove the 2 bolts and No. 1 fuel tank band sub-assembly LH.
Remove the 2 bolts and No. 2 fuel tank band sub-assembly.
Slightly lower the engine lifter.
Be careful not to cut the wiring.
Disconnect the fuel pump connector and sender gauge connector.
Before this procedure, check the connector for dirt, mud or other contamination.
Do not use any tools in this procedure.
Detach the wire harness from the 3 clamps and remove the fuel tank assembly.
17.DISCONNECT FUEL EMISSION HOSE
77209D
18.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
77168A
19.REMOVE FUEL TANK VENT TUBE SET PLATE
20.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP
83320
21.REMOVE FUEL SENDER GAUGE ASSEMBLY
77209D
22.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Detach the 5 clamps and remove the fuel tank main tube sub-assembly.
77026A
23.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Detach the 5 clamps and remove the No. 1 fuel evaporation tube sub-assembly.
77289B
24.REMOVE NO. 3 FUEL TUBE CLAMP
Remove the No. 3 fuel tube clamp from the fuel tank assembly.
77299A
25.REMOVE NO. 5 FUEL TUBE CLAMP
Remove the No. 5 fuel tube clamp from the fuel tank assembly.
77295D
26.REMOVE FUEL TUBE GROMMET
Remove the 3 fuel tube grommets from the fuel tank assembly.
77707
27.REMOVE CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY
Detach the 2 clamps and remove the canister outlet tube sub-assembly from the fuel tank assembly.
28.REMOVE FUEL EMISSION HOSE
| *1 | Retainer |
Pinch the retainer as shown in the illustration, and then remove the fuel emission hose.
Clean off any dirt and foreign matter from the clip before disconnecting the hoses.
Do not use any tools in this procedure.
Do not forcefully bend or twist the nylon tube.
Put the hose in a plastic bag to prevent damage and contamination.
If the connector is stuck, pinch the retainer and push and pull the hose to disconnect it.