Home › General › INTRODUCTION › REPAIR INSTRUCTION › 2015.10–2016.08
RM3090E _V1 General _008731 INTRODUCTION _0049918 REPAIR INSTRUCTION D

INTRODUCTION  REPAIR INSTRUCTION  INITIALIZATION  


PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED


Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for 2WW:(Click here)
for 3ZR-FAE:(Click here)
Correction of steering angle neutral point Panoramic view monitor system function (Click here)
Reset back door close position
·

Power back door function

·

Back door closer function


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation receiver assembly requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed Link
for 2AD-FHV:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FHV:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FHV:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FHV:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 2AD-FHV
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FHV:

Exhaust manifold converter sub-assembly (DPNR catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPNR thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 2AD-FHV:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FHV:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FHV:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AD-FTV, CCo:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FTV, CCo:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FTV, CCo:

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FTV, CCo:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FTV, CCo:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FTV, CCo:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FTV, CCo:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AD-FTV, DPF:

ECM


·

Learning Values Save

·

Learning Values Write


Engine start (Click here)
for 2AD-FTV, DPF:

Engine assembly


·

Clear Crank Time Compensation Data

·

Input Injector Compensation Code

·

Pilot Quantity Learning


·

Engine starting

·

DTC is output


for 2AD-FTV, DPF

No. 1 crankshaft position sensor plate


Clear Crank Time Compensation Data
·

Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data

·

DTC is output


for 2AD-FTV, DPF:

Air fuel ratio sensor


A/F Sensor Compensation Reset
·

EGR volume is affected

·

DTC is output.


for 2AD-FTV, DPF:
·

Supply pump assembly

·

Suction control valve


Supply Pump Initialization
·

Engine start

·

DTC is output


for 2AD-FTV, DPF:

Exhaust manifold converter sub-assembly (DPF catalyst)


Catalyst Record Clear
·

Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement

·

DTC is output


for 2AD-FTV, DPF:

Injector assembly


·

Input Injector Compensation Code

·

After that perform the Pilot Quantity Learning


DTC is output.
for 2AD-FTV, DPF:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AD-FTV, DPF:
·

Diesel throttle body assembly

·

Electric EGR control valve assembly


ECD System initialization Engine start (Click here)
for 2AR-FE, w/ Canister Pump Module:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AR-FE, w/o Canister Pump Module:

ECM


Register VIN DTC P0630 is input (Click here)
for 2AR-FE, w/ Canister Pump Module:
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 2AR-FE, w/o Canister Pump Module:
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 3ZR-FAE:

ECM


Register VIN DTC P0630 is input (Click here)
for 3ZR-FAE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Continuously variable valve lift controller assembly

·

Cylinder head sub-assembly

·

Camshaft housing sub-assembly

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock sensor


Inspection after repair Poor idle, engine starting, etc. (Click here)
for 3ZR-FE:

ECM


Register VIN DTC P0630 is input for K111, K111F:(Click here)
except K111, K111F:(Click here)
for 3ZR-FE:
·

Throttle body assembly

·

Cleaning the deposits from the throttle body assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft

(for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock sensor


Inspection after repair Poor idle, engine starting, etc. for K111, K111F:(Click here)
except K111, K111F:(Click here)
for 2WW:

ECM


·

Learning Values Save

·

Learning Values Write


- (Click here)
for 2WW:

Injector Assembly


Injector Compensation -
for 2WW:

Fuel Supply Pump Assembly


Supply Pump Learning Value Reset -
for 2WW:

Exhaust Manifold Converter Sub-assembly (Catalytic Converter)


·

DPF History Information Reset

·

NOx Storage Catalyst Learning Value Reset


-
for 2WW:

Air Fuel Ratio Sensor


O2 Sensor Learning Value Reset -
for 2WW:

Mass Air Flow Meter


Air Flow Meter Learning Value Reset -
for 2WW:

EGR Valve Assembly


EGR Learning Value Reset -
for 2WW:

Differential Pressure Sensor


Differential Pressure Learning Value Reset -
for 2WW:

Swirl Control Valve


Swirl Valve Learning Value Reset -
for 2WW:

Turbo Pressure Sensor Assembly


Upstream Turbine Pressure Learning Value Reset -
for 2WW:

Pressure Discharge Valve


Fuel PCV Compensation Value Reset -
for 2WW:

Engine assembly


Injector Compensation -
Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly
·

Dynamic radar cruise control system

·

Pre-collision system


(Click here)
·

Forward recognition camera

·

Windshield glass


Adjust forward recognition camera
·

Lane departure alert system (w/ Steering Control)

·

Road sign assist system

·

Dynamic radar cruise control system

·

Forward recognition camera system

·

Pre-crash safety system

·

Automatic high beam system


(Click here)
w/ Stop and Start System:

Engine stop and start ECU


·

Upload the number of starter operations

·

Reset air conditioning information

·

Learning of the air conditioning information

·

Clear the zero point calibration data

·

Perform zero point calibration of the deceleration sensor


Stop and start system for 2WW:(Click here)
for 3ZR-FAE:(Click here)
w/ Stop and Start System:

Starter assembly


NOTICE:
·

for 2WW:

When the starter assembly is replaced, "ST relay" must be also replaced.

·

for 3ZR-FAE, CVT:

When the starter assembly is replaced, "ST NO. 1 relay" and "ST NO. 2 relay" must be also replaced.

·

for 3ZR-FAE, Manual Transaxle:

When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.



Clear the number of starter operations
w/ Stop and Start System:

Air conditioning amplifier assembly


·

Reset air conditioning information

·

Learning of the air conditioning information


w/ Stop and Start System:

Airbag sensor assembly


·

Clear the zero point calibration of the deceleration sensor

·

Perform zero point calibration of the deceleration sensor


w/ Stop and Start System, for 3ZR-FAE:
·

Continuously variable transaxle assembly

·

CVT fluid


Bleed the oil pump assembly with motor (continuously variable transaxle assembly)
w/ Stop and Start System, for 3ZR-FAE:

Vehicle with a nonspecified battery


Perform battery type switching
for U660F:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into TCM

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U660F:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U660F:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow TCM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U660F:

TCM (If possible, read the transaxle compensation code from the previous TCM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new TCM)

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow TCM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U760E:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow ECM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U760E:

ECM (If possible, read the transaxle compensation code from the previous ECM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new ECM)

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

Automatic transaxle assembly


·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for Initialization:(Click here)
for Registration:(Click here)
for U760F:
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

Shift solenoid valve SL1 and/or SL2


Perform road test to allow ECM to learn
·

Large shift shock

·

The deterioration of fuel efficiency


for U760F:

ECM (If possible, read the transaxle compensation code from the previous ECM)


Possible
·

Reset memory

·

Input Transaxle compensation code (Into the new ECM)

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


Impossible
·

Reset memory

·

Initialize transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


for K111:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K111F:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K114:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K114:

CVT fluid


ATF Thermal Degradation Estimate Reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
for K114F:
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


·

Reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration


·

DTC P1589 is output (Malfunction Indicator Lamp (MIL) not illuminates)

·

Deterioration of fuel efficiency


(Click here)
for K114F, w/ Stop and Start System:
·

Continuously variable transaxle assembly

·

CVT fluid


Bleed the oil pump assembly with motor Stop and start system
for K114F:

CVT fluid


ATF Thermal Degradation Estimate Reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
·

4WD ECU assembly

HINT:

When replacing the 4WD ECU assembly with a new one, it is not necessary to perform initialization.


·

Acceleration sensor (airbag sensor assembly)


Clear zero point calibration data Dynamic torque control 4WD/AWD system (Click here)
·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


·

Transmitter ID registration

·

Initialization


Tire pressure warning system for Registration:(Click here)
for Initialization:(Click here)
Skid control ECU (brake actuator assembly) Yaw rate and acceleration sensor zero point calibration. Vehicle stability control system (Click here)
Yaw rate and acceleration sensor (airbag sensor assembly)
·

Clearing zero point calibration data.

·

Yaw rate and acceleration sensor zero point calibration.


Vehicle stability control system (Click here)
Wheel alignment adjustment
·

Clearing zero point calibration data.

·

Yaw rate and acceleration sensor zero point calibration.


Vehicle stability control system (Click here)
Power steering ECU assembly Assist map writing Power steering system (Click here)
w/ Parking Assist Monitor System, for Camera built-in ECU:

Spiral with sensor cable sub-assembly


Steering angle setting Parking assist monitor system (for Camera built-in ECU) (Click here)
w/ Parking Assist Monitor System, for Camera built-in ECU:

Suspension, tires, etc.


Back camera position setting
w/ Parking Assist Monitor System, for Camera built-in ECU:

Television camera assembly


Parking assist monitor system initialization
w/ Panoramic View Monitor System

Spiral with sensor cable sub-assembly


Steering angle neutral point (Initialize panoramic view monitor system) Panoramic viewmonitor system (Click here)
w/ Panoramic View Monitor System

Navigation receiver assembly*2 or Radio and display receiver assembly*3


Panoramic view monitor system initialization
w/ Panoramic View Monitor System

Parking assist ECU


·

Parking assist ECU initialization

·

Adjust steering angle


w/ Panoramic View Monitor System

Suspension, tires, etc.


Adjust steering angle
w/ Panoramic View Monitor System

Rear television camera assembly


Rear television camera view adjustment
w/ Panoramic View Monitor System

Front television camera assembly


Front television camera view adjustment
w/ Panoramic View Monitor System
·

Side television camera assembly LH

·

Outer rear view mirror assembly LH


Side television camera view adjustment
w/ Panoramic View Monitor System
·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


Side television camera view adjustment
w/ Panoramic View Monitor System
·

Front television camera assembly or radiator grille assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment
w/ Entry and Start System:
·

Certification ECU (smart key ECU assembly)

·

ID code box (immobiliser code ECU)*1

·

ECM

·

Steering lock ECU (steering lock actuator assembly)

·

Electrical key transmitter sub-assembly


Registration
·

Wireless door lock operation

·

Entry operation

·

Engine starting

·

Steering unlock


Refer to the Service Bulletin for the registration method
w/o Entry and Start System:
·

Transponder key ECU assembly

·

ECM

·

Electrical key transmitter sub-assembly


Registration Engine starting Refer to the Service Bulletin for the registration procedure
w/o Entry and Start System:
·

Door control transmitter

·

Door control receiver


Register recognition code Wireless door lock operation (Click here)
·

Occupant detection ECU

·

Front seat assembly RH (occupant classification sensor)


·

Zero point calibration

·

Sensitivity check


·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)
for Automatic Air Condition System:
·

Air conditioning amplifier assembly

·

No. 1 Air conditioning radiator damper servo sub-assembly

·

No. 2 Air conditioning radiator damper servo sub-assembly

·

No. 3 Air conditioning radiator damper servo sub-assembly

·

No. 1 Blower mode damper servo sub-assembly


Initialization servo motor Initialization servo motor (Click here)
w/ Jam Protection Function:
·

Frontpower window regulator motor assembly LH (for LHD)

·

Front power window regulator motor assembly RH (for RHD)

·

Power window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up/down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)
·

Sliding roof drive gear sub-assembly (sliding roof ECU)

·

Sliding roof glass sub-assembly

·

Sliding roof drive cable sub-assembly


Initialize sliding roof ECU (pulse sensor initial position setting)
·

Automatic slide open/close and tilt up/down function of sliding roof

·

Jam protection function

·

Operation function after ignition off

·

Sliding roof open warning


(Click here)
w/ Power Back Door System:

Back door lock assembly


Initialize back door closer system Back door lock operation (Click here)
w/ Power Back Door System:

Multiplex network door ECU


Initialize power back door system Power back door system (Click here)
·

Height control sensor

·

Headlight leveling ECU


Height leveling ECU initialization Height leveling function (Click here)


*1: w/ ID code box (Immobiliser Code ECU)

*2: w/ Navigation System

*3: w/ Audio and Visual System (for Radio and Display Type)