Home › Engine / Hybrid System › 3ZR-FE ENGINE CONTROL › SFI SYSTEM(for K111, K111F) › from 2015.10
RM3090E _51 Engine / Hybrid System _008380 3ZR-FE ENGINE CONTROL _0219876 SFI SYSTEM(for K111, K111F) C

3ZR-FE ENGINE CONTROL  SFI SYSTEM(for K111, K111F)  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0115.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(for K111, K111F)>P0115

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Circuit Range / Performance Problem Either condition is met (2 trip detection logic):
·

When engine is started cold and warmed up, the engine coolant temperature sensor value does not change.

·

After the warmed up engine is stopped and the next cold engine start is performed, the engine coolant temperature sensor value does not change.


·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored

MONITOR DESCRIPTION

Engine coolant temperature sensor cold start monitor

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.


Engine coolant temperature sensor soak monitor

If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and the DTC is stored.


CONFIRMATION DRIVING PATTERN

A198823E42
0.854,1.135 1.99,1.417 1.135,0.281 10 40 km/h 1.021,1.771 1.417,2 0.396,0.229 10 Idling 2.771,2.531 3.917,2.75 1.146,0.219 10 5 minutes or more 4.167,0.208 5.833,0.417 1.667,0.208 10 Total of 5 minutes or more 2.115,1.917 2.417,2.167 0.302,0.25 10 [A] 3.25,1.646 3.5,1.917 0.25,0.271 10 [B] 3.99,2.875 4.229,3.115 0.24,0.24 10 [C] 6.146,2.865 6.417,3.083 0.271,0.219 10 [E] 0.229,2.042 1.417,2.25 1.188,0.208 10 Ignition Switch ON 4.865,0.656 5.167,0.917 0.302,0.26 10 [D] 1.385,3.146 6.5,3.417 5.115,0.271 10 HINT: Start the engine when the engine coolant temperature is 60°C (140°F) or less

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

4.

Check that the engine coolant temperature is 60°C (140°F) or less.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or higher, the engine coolant temperature sensor is malfunctioning. It is not necessary to continue this procedure.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0116.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


15.

Check the DTC judgment result again [E].

HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.



CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117 or P0118 are output simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

When the DTC is output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0116 is output A
DTC P0116 and other DTCs are output B


HINT:

If any DTCs and other than P0116 are output, troubleshoot those DTCs first.




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

Inspect the thermostat (opening temperature).

Click hereEngine / Hybrid System>3ZR-FE COOLING>THERMOSTAT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(for K111, K111F)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG