Home › Engine / Hybrid System › 3ZR-FE INTAKE / EXHAUST › EXHAUST PIPE › from 2015.10
RM3090E _51 Engine / Hybrid System _008408 3ZR-FE INTAKE / EXHAUST _0046967 EXHAUST PIPE A

3ZR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum free length:

41.5 mm (1.63 in.)


If the free length is less than the minimum, replace the compression spring.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.
A076194C09
2.031,1.583 1.563,1.719 1.563,1.719 1.396,1.719 true 2.438,0.979 3.042,0.979 true 1.188,1.625 1.406,1.802 0.219,0.177 10 *1 3.063,0.885 3.281,1.063 0.219,0.177 10 *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




d.

Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17420 2.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Connect the 3 exhaust pipe supports to install the center exhaust pipe assembly.


c.

Install the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum free length:

38.5 mm (1.52 in.)


If the free length is less than the minimum, replace the compression spring.


b.
A076194C06
2.031,1.583 1.563,1.719 1.563,1.719 1.396,1.719 true 2.438,0.979 3.042,0.979 true 1.188,1.625 1.406,1.802 0.219,0.177 10 *1 3.063,0.885 3.281,1.063 0.219,0.177 10 *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the tail exhaust pipe assembly, do not push in the gasket with the tail exhaust pipe assembly.




c.

Connect the 2 exhaust pipe supports to install the tail exhaust pipe assembly.


d.

Install the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 89465 4.CONNECT HEATED OXYGEN SENSOR

NOTICE:

Do not strike the metal part of the heated oxygen sensor.


a.

Rotate the heated oxygen sensor counterclockwise the same number of times as recorded in the removal procedure, and then connect it to the center exhaust pipe assembly by hand.

NOTICE:

After rotating the heated oxygen sensor counterclockwise the same number of times as in the removal procedure, connect it while making sure that the wire harness is not twisted.



b.
A209092C01
2.302,1.042 1.958,0.281 1.958,0.281 2.271,0.281 true 1.073,2.375 1.385,2.531 0.313,0.156 10 *1 2.323,0.219 2.781,0.417 0.458,0.198 10 SST
*1 Fulcrum Length


Using SST, tighten the heated oxygen sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


·

Make sure SST and the wrench are connected in a straight line.




c.

Connect the grommet to the floor panel.


Hide 5.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

HINT:

If an exhaust gas leak has been repaired, perform an inspection following the repair.



Hide 6.INSTALL NO. 2 ENGINE UNDER COVER (w/ Cover)

Hide 50819 7.INSTALL FRONT FLOOR COVER (w/ Cover)