As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.
for Manual Transaxle:
When the transaxle is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder assembly to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.
Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly, camshaft, No. 2 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly, piston sub-assembly or piston ring.
for K111, K111F:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(for K111, K111F)>INITIALIZATION
except K111, K111F:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM(except K111, K111F)>INITIALIZATION
12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator is necessary.
Temporarily install the engine mounting insulator LH with the 4 bolts.
Tighten the 4 bolts in the sequence shown in the illustration.
Install the wire harness clamp bracket with the bolt.
12305
2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator is necessary.
Temporarily install the engine mounting insulator sub-assembly RH with the 3 bolts.
Tighten the 3 bolts in the sequence shown in the illustration.
Install the radiator reservoir bracket with the bolt.
12371A
3.INSTALL REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Temporarily install the rear engine mounting insulator with the 2 bolts and 2 nuts.
| *A | for 2WD | *B | for 4WD / AWD |
| *C | for Manual Transaxle | *D | for CVT |
Tighten the 2 bolts and 2 nuts in the sequence shown in the illustration.
43457
4.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.
5.INSTALL ENGINE HANGER
6.REMOVE ENGINE FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach an engine sling device and hang the engine with a chain block.
Lift the engine and remove it from the engine stand.
7.FIX ENGINE ASSEMBLY
82121
8.INSTALL ENGINE WIRE
Install the engine wire to the engine.
13405
9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
31400
10.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)
31407B
11.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)
12.INSTALL CLUTCH TUBE (for Manual Transaxle)
31250
13.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)
31210
14.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)
31210
15.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)
32101
16.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
30300
17.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)
for 4WD/AWD
Click hereDrivetrain>EB61F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE ASSEMBLY>INSTALLATION
30400
18.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>INSTALLATION
36100
19.INSTALL TRANSFER ASSEMBLY (for 4WD/AWD)
11363A
20.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
21.INSTALL STARTER ASSEMBLY
for 1.0 kW
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTER(for 1.0 kW Type)>INSTALLATION
for 1.3 kW
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTER(for 1.3 kW Type)>INSTALLATION
45319A
22.INSTALL STEERING GEAR HEAT INSULATOR (for RHD)
23.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Temporarily install the front engine mounting insulator with the through bolt and nut.
| *1 | Alignment Mark |
| *2 | Protrusion |
Temporarily install the front suspension crossmember with the through bolt.
When installing the suspension crossmember, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.
Place the engine on an engine lifter.
Place the engine on wooden blocks or equivalent so that the engine is level.
Operate the engine lifter and install the engine to the vehicle.
Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine is clear of all wiring and hoses.
While raising the engine into the vehicle, do not allow it to contact the vehicle.
Temporarily install the front suspension crossmember with the 2 bolts.
Temporarily install the front suspension member brace rear RH and LH with the 6 bolts.
Install the engine mounting insulator LH with the through bolt and nut.
While holding the bolt in place, tighten the nut.
Install the engine mounting insulator RH with the bolt and 2 nuts.
Tighten the 2 front suspension crossmember sub-assembly bolts.
|
Bolt A |
|
Bolt B |
Tighten the 6 front suspension member brace rear bolts.
Remove the 2 bolts and No. 1 and No. 2 engine hangers.
Install the air fuel ratio sensor bracket with the bolt. Then connect the air fuel ratio sensor connector.
Attach the fuel tube clamp.
|
Bolt A |
|
Bolt B |
Install the front crossmember sub-assembly with the 6 bolts.
Tighten the through bolt of the rear engine mounting insulator.
Check that the protrusion of the engine mounting bracket is aligned with the alignment mark of the engine mounting insulator.
Tighten the through bolt and nut of the front engine mounting insulator.
While holding the nut in place, tighten the through bolt.
51218A
24.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH
Install the front suspension member reinforcement LH with the 4 bolts.
51217A
25.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
Install the front suspension member reinforcement RH with the 4 bolts.
51425B
26.INSTALL FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT (for 2WD)
Install the front lower engine mounting bracket reinforcement with the 2 bolts.
32101A
27.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>INSTALLATION
37100
28.TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)
37100
29.TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)
89465
30.CONNECT HEATED OXYGEN SENSOR (for 4WD/AWD)
17410
31.INSTALL FRONT EXHAUST PIPE ASSEMBLY
43420
32.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43420G
33.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
43410
34.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
48069
35.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
36.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
45047
37.CONNECT TIE ROD END SUB-ASSEMBLY LH
45046
38.CONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
48810
39.CONNECT FRONT STABILIZER LINK ASSEMBLY LH
48820B
40.CONNECT FRONT STABILIZER LINK ASSEMBLY RH
Use the same procedure described for the LH side.
41.CONNECT FRONT SPEED SENSOR LH
42.CONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
43502H
43.INSTALL FRONT AXLE SHAFT NUT LH
43501H
44.INSTALL FRONT AXLE SHAFT NUT RH
Use the same procedure described for the LH side.
45025D
45.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45260
46.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
47.INSTALL COLUMN HOLE COVER SILENCER SHEET
48.CONNECT CLUTCH HOSE (for Manual Transaxle)
Connect the clutch hose and install a new clip to the clutch hose.
Install the clip as far as it will go.
Using a 10 mm union nut wrench, connect the clutch hose to the accumulator to flexible hose tube while holding the flexible hose.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Do not kink or damage the clutch release cylinder tube.
Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder tube from the clip or bracket.
This torque value is effective when the union nut wrench is parallel to the torque wrench.
49.CONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for CVT)
Connect the clamp of the transaxle control cable assembly with the bolt.
Connect the transaxle control cable assembly to the control cable support.
Connect the transaxle control cable assembly to the bracket with a new clip.
Connect the transaxle control cable assembly to the control shaft lever with the nut.
33820B
50.CONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Connect the transaxle control cable assembly to the control cable bracket and install 2 new clips.
Connect the transaxle control cable assembly to the transaxle and install the 2 clips.
51.CONNECT WIRE HARNESS AND HOSE
Connect the heater water outlet hose and heater water inlet hose to the heater core and slide the 2 clamps to secure the hoses.
Connect the connector tube hose to the air tube and slide the clamp to secure it.
for Manual Transaxle:
Attach the clamp and connect the engine wire to the manual transaxle with the bolt.
for CVT:
Attach the clamp and connect the engine wire to the CVT with the bolt.
Attach the wire harness clamp.
Connect the starter wire with the nut, and then connect the terminal cap.
Attach the 2 claws to install the wire harness to the engine room No. 1 junction block.
Connect the 2 wire harness connectors to the engine room No. 1 junction block and install the nut.
Attach the 2 clamps and install the bolt.
23901
52.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly and then install the No. 1 fuel pipe clamp.
Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION
16571
53.CONNECT NO. 1 RADIATOR HOSE
for CVT:
Connect the breather plug hose to the clamp.
Connect the No. 1 radiator hose to the cylinder head and slide the clamp to secure it.
89661
54.INSTALL ECM
74414B
55.INSTALL BATTERY BRACKET REINFORCEMENT
74411B
56.INSTALL FRONT BATTERY BRACKET
16057
57.CONNECT RADIATOR HOSE SUB-ASSEMBLY
74431
58.INSTALL BATTERY TRAY
28800
59.INSTALL BATTERY
74404A
60.INSTALL BATTERY CLAMP SUB-ASSEMBLY
61.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17705
62.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
88310
63.CONNECT COMPRESSOR WITH PULLEY ASSEMBLY
Using an E8 "TORX" socket wrench, connect the compressor with pulley assembly with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
Tighten the bolts and nuts in the order shown in the illustration.
Connect the connector.
16572D
64.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet and slide the clamp to secure it.
27020
65.INSTALL GENERATOR ASSEMBLY
for 100 A Type:
Click herePower Source / Network>3ZR-FE BATTERY / CHARGING>GENERATOR(for 100 A Type)>INSTALLATION
for 130 A Type:
Click herePower Source / Network>3ZR-FE BATTERY / CHARGING>GENERATOR(for 130 A Type)>INSTALLATION
16361A
66.INSTALL V-RIBBED BELT
16361A
67.ADJUST V-RIBBED BELT
16470
68.CONNECT RADIATOR RESERVOIR ASSEMBLY
Connect the radiator reservoir assembly with the 2 bolts.
Connect the No. 1 and No. 2 water by-pass hoses to the radiator reservoir assembly and slide the 2 clamps to secure the hoses.
69.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
70.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
for 4WD/AWD
Click hereDrivetrain>EB61F MANUAL TRANSMISSION / TRANSAXLE>MANUAL TRANSAXLE OIL>REPLACEMENT
71.ADD ENGINE COOLANT
72.ADD ENGINE OIL
73.ADD TRANSFER OIL (for 4WD / AWD)
74.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
75.INSPECT SHIFT LEVER POSITION (for CVT)
76.INSPECT FOR FUEL LEAK
77.INSPECT FOR COOLANT LEAK
78.INSPECT FOR OIL LEAK
79.INSPECT FOR EXHAUST GAS LEAK
16361A
80.INSPECT V-RIBBED BELT
81.INSPECT IGNITION TIMING
82.INSPECT ENGINE IDLE SPEED
83.INSPECT CO/HC
84.ADJUST FRONT WHEEL ALIGNMENT
85.INSTALL NO. 2 ENGINE UNDER COVER (w/ Cover)
Install the No. 2 engine under cover with the bolt and clip.
50819
86.INSTALL FRONT FLOOR COVER (w/ Cover)
51443
87.INSTALL REAR ENGINE UNDER COVER RH
Install the rear engine under cover RH with the 3 clips.
51444
88.INSTALL REAR ENGINE UNDER COVER LH
Install the rear engine under cover LH with the 3 clips.
51441
89.INSTALL NO. 1 ENGINE UNDER COVER
11212
90.INSTALL NO. 2 CYLINDER HEAD COVER
91. RESET MEMORY
for 4WD/AWD
Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION