Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0148247 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and also the radio and display receiver assembly itself cannot function.

WIRING DIAGRAM

E333601E03
1.292,2.375 1.74,2.74 0.448,0.365 10 false OFF HOOK 0.635,1.323 0.99,1.5 0.354,0.177 10 false VOL- 1.375,1.323 1.76,1.5 0.385,0.177 10 false VOL+ 1.969,1.313 2.427,1.49 0.458,0.177 10 false SEEK- 2.635,2.458 3.25,2.656 0.615,0.198 10 false MODE 0.563,2.458 1,2.656 0.438,0.198 10 false VOICE 1.99,2.365 2.427,2.729 0.438,0.365 10 false ON HOOK 2.635,1.323 3.167,1.51 0.531,0.188 10 false SEEK+ 1.521,3.396 3.344,3.594 1.823,0.198 10 false Steering Pad Switch LH Side 1.51,3.927 3.469,4.156 1.958,0.229 10 false Steering Pad Switch Assembly 4.583,0.792 5.198,0.99 0.615,0.198 10 false z1 4.573,1.896 5.188,2.094 0.615,0.198 10 false z1 4.594,3 5.208,3.198 0.615,0.198 10 false z1 4.573,0.583 4.896,0.781 0.323,0.198 10 false 11 4.625,1.698 4.948,1.896 0.323,0.198 10 false 8 4.573,2.792 4.896,2.99 0.323,0.198 10 false 10 4.948,0.688 5.563,0.885 0.615,0.198 10 false AU1 4.948,1.771 5.563,1.969 0.615,0.198 10 false EAU 4.979,2.885 5.594,3.083 0.615,0.198 10 false AU2 5.427,0.792 6.042,0.99 0.615,0.198 10 false G8 5.417,1.896 6.031,2.094 0.615,0.198 10 false G8 5.417,3.01 6.031,3.208 0.615,0.198 10 false G8 5.469,0.583 6.083,0.781 0.615,0.198 10 false 6 5.479,1.698 6.094,1.896 0.615,0.198 10 false 3 5.479,2.802 6.094,3 0.615,0.198 10 false 5 5.99,0.667 6.604,0.865 0.615,0.198 10 false 21 5.979,1.771 6.594,1.969 0.615,0.198 10 false 23 6,2.885 6.615,3.083 0.615,0.198 10 false 22 6.292,0.792 6.906,0.99 0.615,0.198 10 false SW1 6.292,1.885 6.906,2.083 0.615,0.198 10 false SWG 6.302,3 6.917,3.198 0.615,0.198 10 false SW2 4.521,3.885 5.792,4.24 1.271,0.354 10 false Spiral with Sensor Cable Sub-assembly 5.917,3.781 6.302,3.969 0.385,0.188 10 false G143 5.938,3.958 7.125,4.313 1.188,0.354 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>PRECAUTION

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the G8 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-21 (SW1) - G8-6 (AU1) Always Below 1 Ω
G143-22 (SW2) - G8-5 (AU2) Always Below 1 Ω
G143-23 (SWG) - G8-3 (EAU) Always Below 1 Ω
G143-21 (SW1) - Body ground Always 10 kΩ or higher
G143-22 (SW2) - Body ground Always 10 kΩ or higher
G143-23 (SWG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR