Home › Drivetrain › K114 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _044380 K114 MULTIDRIVE / CVT _0220923 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly). If a malfunction in the yaw rate and acceleration sensor (airbag sensor assembly) is determined based on a malfunction signal from the skid control ECU (brake actuator assembly), the ECM stores this DTC.

HINT:
·

The yaw rate and acceleration sensor (airbag sensor assembly) signal is sent to the skid control ECU (brake actuator assembly) via CAN communication.

·

If CAN communication DTCs are output, perform troubleshooting for those DTCs first.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

The ignition switch is ON.

2.

The output value of the yaw rate and acceleration sensor (airbag sensor assembly) remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

0.5 seconds or more

4.

1-trip detection logic


DTC Detection Condition 2:
1.

The ignition switch is ON.

2.

The power source voltage to the yaw rate and acceleration sensor (airbag sensor assembly) remains at 4.4 V or less, or 5.6 V or higher for 1.2 seconds or more.

3.

0.5 seconds or more

4.

1-trip detection logic


DTC Detection Condition 3:
1.

The ignition switch is ON.

2.

No signal from the yaw rate and acceleration sensor (airbag sensor assembly) is detected 7 times or more.

3.

0.5 seconds or more

4.

1-trip detection logic


DTC Detection Condition 4:
1.

The ignition switch is ON.

2.

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

3.

0.5 seconds or more

4.

1-trip detection logic


DTC Detection Condition 5:
1.

The ignition switch is ON.

2.

A yaw rate and acceleration sensor (airbag sensor assembly) power source voltage malfunction signal is received for 10 seconds or more with the vehicle speed at 3 km/h (1.8 mph) or more.

3.

0.5 seconds or more

4.

1-trip detection logic


·

Yaw rate and acceleration sensor (airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)

·

CAN communication system


Does not come on DTC stored

WIRING DIAGRAM

C347476E01
1.323,1.479 3.417,1.865 2.094,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 1.333,3.833 3.479,4.208 2.146,0.375 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 5.823,3.698 6.281,3.896 0.458,0.198 10 false ECM 0.469,5.323 4.135,5.521 3.667,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC U0129 is not output A
DTC U0129 is output B



A

2.READ VALUE USING GTS (G SENSOR)

B

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of G sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of G sensor
·

2.31 V to 2.69 V: Vehicle on level ground

·

1.88 V to 2.5 V: Decelerating

·

2.5 V to 3.11 V: Accelerating

·

Set to 1.87 V: G sensor malfunction

·

Set to 1.87 V: Communication malfunction


-
Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

3.REPLACE AIRBAG SENSOR ASSEMBLY

B

3.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT