The ECM memory contains programs for normal and sport shift patterns.
By following the programs corresponding to the signals from the combination switch assembly, the park/neutral position switch and other various sensors, the ECM switches the shift control solenoid valves on and off, and controls the transaxle gear ratio.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| *1 | Combination Switch Assembly |
w/o Stop and Start System:
Remove the combination switch assembly.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>PATTERN SELECT SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (MSW1) - 4 (MSW2) | Combination switch assembly (SPORT) on | Below 1 Ω |
| 2 (MSW1) - 4 (MSW2) | Combination switch assembly (SPORT) off | 10 kΩ or higher |
| *1 | Combination Switch Assembly |
w/ Stop and Start System:
Remove the combination switch assembly.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>PATTERN SELECT SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (MSW1) - 5 (MSW2) | Combination switch assembly (SPORT) on | Below 1 Ω |
| 2 (MSW1) - 5 (MSW2) | Combination switch assembly (SPORT) off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Combination Switch Assembly) |
w/o Stop and Start System:
Disconnect the combination switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-4 (MSW2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Combination Switch Assembly) |
w/ Stop and Start System:
Disconnect the combination switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G185-5 (MSW2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A62-57 (PWMS) - Body ground | Combination switch assembly (SPORT) on | Below 1 Ω |
| A62-57 (PWMS) - Body ground | Combination switch assembly (SPORT) off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT