DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When selecting a measurement group, the ECM data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Check Mode / Check mode related data
AT / Automatic transaxle system related data
Vehicle Information / Vehicle information
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. ·
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
·
0 rpm: Engine stopped (ignition switch ON) ·
No large changes in engine speed: Driving at a constant speed |
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| MAF | Airflow rate from mass air flow meter sub-assembly | Min.: 0 gm/sec.
Max.: 655.35 gm/sec. |
·
1.0 to 3.0 gm/sec: Idling ·
3.0 to 8.0 gm/sec: 3000 rpm (without load) |
This is the intake air amount from the mass air flow meter sub-assembly. |
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | ·
After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F). ·
After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal. ·
Check if the engine is overheating if the value indicates 140°C (284°F). |
| Throttle Motor DUTY | Throttle actuator | Min.: 0%
Max.: 100% |
10 to 22%: Idling | This is the output duty ratio of the throttle actuator drive circuit. |
| N Range Status | Judgment for shift lever N position | OFF or ON | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Starter Signal | Starter signal | OFF or ON | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Neutral Position SW Signal | Park/neutral position switch status | OFF or ON | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status | OFF or ON | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| A/C Signal | A/C switch status | OFF or ON | ON: A/C on | - |
| Closed Throttle Position SW | Closed throttle position switch | OFF or ON | ·
ON: Throttle fully closed ·
OFF: Throttle open |
- |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | OFF or ON | - | - |
| SPD (NT) | Input turbine speed | Min.: 0 rpm
Max.: 12750 rpm |
·
Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine) ·
Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N) ·
0 rpm: Vehicle stopped with shift lever in R |
Data is displayed in increments of 50 rpm. |
| Shift SW Status (P Range) | Park/neutral position switch status | OFF or ON | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Kick Down Switch Status | Kick down switch status | OFF or ON | ·
ON: Accelerator pedal fully depressed ·
OFF: Accelerator pedal released |
- |
| Pattern Switch (PWR/M) | Sport mode status | OFF or ON | ·
ON: Sport mode on ·
OFF: Sport mode off |
- |
| Shift SW Status (R Range) | Park/neutral position switch status | OFF or ON | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch status | OFF or ON | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported | Shift lever position P or N support status | Supp or Unsupp | Supp: Normal | - |
| Shift SW Status (N,P Range) | Park/neutral position switch status | OFF or ON | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Sports Shift Up SW | Sport shift up switch status | OFF or ON | ·
ON: Shift lever held in "+" ·
OFF: Shift lever not held in "+" ·
ON: "+" shift paddle operated and held (up-shift)*2 ·
OFF: "+" shift paddle not operated (up-shift)*2 |
- |
| Sports Shift Down SW | Sport shift down switch status | OFF or ON | ·
ON: Shift lever held in "-" ·
OFF: Shift lever not held in "-" ·
ON: "-" shift paddle operated and held (down-shift)*2 ·
OFF: "-" shift paddle not operated (down-shift)*2 |
- |
| Sports Mode Selection SW | Sport mode select switch status | OFF or ON | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Shift SW Status (D Range) | Park/neutral position switch status | OFF or ON | ·
ON: Shift lever in D or M ·
OFF: Shift lever not in D or M |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| A/T Oil Temperature 1 | CVT fluid temperature sensor value | Min.: -40°C (-40°F)
Max.: 150°C (302°F) |
·
After stall speed test: approximately 100°C (212°F) ·
Equal to ambient temperature when cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or higher, the CVT fluid temperature sensor circuit is open or shorted. |
| ATF Thermal Degradation Estimate | Estimated value of CVT fluid thermal degradation | Min.: 0
Max.: 65535 |
- | If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the CVT fluid is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the CVT fluid. |
| NT Sensor Voltage | Input turbine speed (NT) sensor output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| SPD (NIN) | Primary pulley speed (NIN) | Min.: 0 rpm
Max.: 12750 rpm |
·
0 rpm: Vehicle stopped ·
Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine) |
Data is displayed in increments of 50 rpm. |
| SPD (NOUT) | Secondary pulley speed (NOUT) | Min.: 0 rpm
Max.: 12750 rpm |
·
0 rpm: Vehicle stopped ·
Approximately 2600 rpm: Vehicle cruising at approximately 60 km/h (37 mph) |
Data is displayed in increments of 50 rpm. |
| NOUT Sensor Voltage | Secondary pulley speed (NOUT) sensor output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
3ZR-FAE:
·
3.5 to 4.5 MPa (35.7 to 45.9 kgf/cm2, 508 to 653 psi): D position stall speed test ·
2.5 to 4.5 MPa (25.5 to 45.9 kgf/cm2, 363 to 653 psi): R position stall speed test ·
0.140 to 0.400 MPa (1.4 to 4.1 kgf/cm2, 20 to 58 psi): With shift lever in D, engine is stopped by start and stop system (oil pump assembly with motor is operating) 3ZR-FE:
·
3.1 to 4.5 MPa (31.6 to 45.9 kgf/cm2, 450 to 653 psi): D position stall speed test ·
2.1 to 4.5 MPa (21.4 to 45.9 kgf/cm2, 305 to 653 psi): R position stall speed test |
- |
| G Sensor | Converted output voltage of G sensor | Min.: 0 V
Max.: 79.998 V |
Displays converted voltage of G sensor
·
2.31 V to 2.69 V: Vehicle on level ground ·
1.88 V to 2.5 V: Decelerating ·
2.5 V to 3.11 V: Accelerating ·
Set to 1.87 V: G sensor malfunction ·
Set to 1.87 V: Communication malfunction |
- |
| Lock Up | Lock-up | OFF or ON | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gearshift command | 1st, 2nd, 3rd, 4th or 5th | Same as actual shift position | *3 |
| Solenoid (SLS) | Shift solenoid valve SLS status | OFF or ON | ·
ON: After engine start ·
OFF: Ignition switch ON |
- |
| SLU Solenoid Status | Shift solenoid valve SLU status | OFF or ON | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| SL Solenoid Status | Shift solenoid valve SL status | OFF or ON | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Solenoid(SC) | Shift solenoid valve SC status | OFF or ON | ·
ON: For 1 second after moving shift lever from P to D or R, or N to D or R ·
ON: Lock-up ON to OFF ·
OFF: Engine idling |
- |
| Solenoid(SLP) | Shift solenoid valve SLP status | OFF or ON | ·
ON: After engine start ·
OFF: Ignition switch ON |
- |
| G Sensor Calibration | G sensor calibration status | Incomplete or Complete | Complete | - |
| G Sensor Learning Value | G sensor learned value voltage | Min.: 0 V
Max.: 79.998 V |
2.31 to 2.69 V: G sensor calibration complete | - |
| CVT Oil Press Calibration | CVT oil pressure calibration status | Incompl or Compl | Compl | - |
| Stop&Start of Eng State | Stop and start system engine status | IG, Run, Stopreq, Stop or Restart | - | - |
*1: Refer to DTC P0705.
Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P0705
*2: w/ Shift Paddle Switch
*3: "Shift Status" is a signal divided into 5 gear positions for Active Test.
It does not express gear ratios for normal driving and gear positions for 7-speed sport sequential shiftmatic mode.
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. (Vehicle Condition) Perform with the ignition switch ON, the engine stopped and the shift lever in P. |
| Activate the Solenoid (SLU) | Operate shift solenoid valve SLU | ON or OFF | (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N. |
| Activate the Lock Up | Operate the Lock-up | ON or OFF | Used to check lock-up operation.
Perform "Activate the Lock Up" while monitoring the engine speed and SPD (NT). (Vehicle Condition) Perform at a vehicle speed of 60 km/h (37 mph) or more. |
| Activate the Solenoid (SL) | Operate shift solenoid valve SL | ON or OFF | (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N. |
| Control the Shift Position | Operates the shift solenoid valves to allow the gear position to be manually selected (1st - 2nd - 3rd - 4th - 5th)
Reference gear ratios: 1st (2.48 gear ratio max.) - 2nd (1.46) - 3rd (1.0) - 4th (0.7) - 5th (0.4 gear ratio min.) |
·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Used to check the operation of the shift solenoid valves.
(Vehicle Condition) Perform at a vehicle speed between 20 km/h (12 mph) and 45 km/h (28 mph). |
| Control the SLS Pressure | Operate shift solenoid valve SLS | High or Low | (Vehicle Condition)
Perform with the ignition switch ON and the engine running. |
| Activate the Solenoid (SLS) | Operate shift solenoid valve SLS | ON or OFF | (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N. |
| Activate the Solenoid(SC) | Operate shift solenoid valve SC | ON or OFF | (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N. |
| Activate the Solenoid(SLP) | Operate shift solenoid valve SLP | ON or OFF | (Vehicle Condition)
Perform with the ignition switch ON, the engine stopped and the shift lever in P or N. |