Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly and shift lever assembly (transmission control switch) detect the shift lever position and send signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

The ignition switch is ON and battery voltage is 10.5 V or higher.

2.

2 or more of the following signals are ON simultaneously:

- (NSW, P, N) input signal

- R input signal

- D input signal

3.

2 seconds

4.

2-trip detection logic


DTC Detection Condition 2:
1.

The ignition switch is ON and battery voltage is 10.5 V or higher.

2.

All of the following signals are OFF simultaneously:

- NSW input signal

- P input signal

- R input signal

- N input signal

- D input signal

3.

60 seconds

4.

2-trip detection logic


DTC Detection Condition 3:
1.

The ignition switch is ON and battery voltage is 10.5 V or higher.

2.

Any of the following signals and the M signal are ON simultaneously:

- NSW input signal

- P input signal

- R input signal

- N input signal

3.

2 seconds

4.

2-trip detection logic


·

Harness or connector

·

Park/neutral position switch assembly

·

Shift lever assembly (Transmission control switch)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM. For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or M).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM illuminates the MIL and stores this DTC.

WIRING DIAGRAM

C277058E24
2.427,5.833 4.635,6.229 2.208,0.396 10 false Shift Lever Assembly (Transmission Control Switch) 2.427,5.646 2.885,5.844 0.458,0.198 10 false G36 0.24,5.177 2,5.385 1.76,0.208 10 false from ECU-IG NO. 1 Fuse 0.604,2.688 2.01,2.885 1.406,0.198 10 false from GAUGE Fuse 0.667,1.177 2.063,1.438 1.396,0.26 10 false to ST NO. 1 Relay 2.063,4.229 4.521,4.448 2.458,0.219 10 false Park/Neutral Position Switch Assembly 2.063,4.052 3.021,4.219 0.958,0.167 10 false B36*1, B101*2 2.802,1.094 3.135,1.313 0.333,0.219 10 false L 2.542,1.094 2.875,1.313 0.333,0.219 10 false 9 3.563,1.094 3.896,1.313 0.333,0.219 10 false B 3.781,1.104 4.115,1.323 0.333,0.219 10 false 4 3.5,1.677 3.844,1.896 0.344,0.219 10 false DL 3.792,1.677 4.125,1.896 0.333,0.219 10 false 7 3.5,2.292 3.844,2.51 0.344,0.219 10 false NL 3.792,2.292 4.125,2.51 0.333,0.219 10 false 8 3.5,2.885 3.844,3.104 0.344,0.219 10 false RL 3.792,2.885 4.125,3.104 0.333,0.219 10 false 2 3.5,3.49 3.844,3.708 0.344,0.219 10 false PL 3.781,3.49 4.115,3.708 0.333,0.219 10 false 3 2.802,2.563 3.135,2.781 0.333,0.219 10 false RB 2.563,2.563 2.896,2.781 0.333,0.219 10 false 1 5.26,1.198 5.667,1.479 0.406,0.281 10 false A62 5.615,1.198 6.073,1.396 0.458,0.198 10 false NSW 5.313,1.01 5.563,1.24 0.25,0.229 10 false 23 5.313,1.615 5.563,1.844 0.25,0.229 10 false 65 5.26,1.792 5.781,2.021 0.521,0.229 10 false B93 5.615,1.802 6.073,2 0.458,0.198 10 false D 5.26,2.385 6,2.615 0.74,0.229 10 false B93 5.26,2.99 5.906,3.219 0.646,0.229 10 false B93 5.26,3.583 6.021,3.813 0.76,0.229 10 false B93 5.26,5.177 5.615,5.406 0.354,0.229 10 false A62 5.313,2.208 5.563,2.438 0.25,0.229 10 false 69 5.313,2.802 5.563,3.031 0.25,0.229 10 false 64 5.313,3.406 5.563,3.635 0.25,0.229 10 false 70 5.313,4.979 5.563,5.208 0.25,0.229 10 false 59 5.615,2.396 6.073,2.594 0.458,0.198 10 false N 5.615,3 6.073,3.198 0.458,0.198 10 false R 5.615,3.594 6.073,3.792 0.458,0.198 10 false P 5.615,5.188 6.073,5.385 0.458,0.198 10 false S 3.573,5.083 3.948,5.26 0.375,0.177 10 false S 2.792,5.073 3.167,5.25 0.375,0.177 10 false IG 3.781,5.083 4.115,5.302 0.333,0.219 10 false 5 2.583,5.083 2.917,5.302 0.333,0.219 10 false 4 5.76,5.813 6.115,6.01 0.354,0.198 10 false ECM 0.083,6.26 1.969,6.448 1.885,0.188 10 false *1: for 3ZR-FAE 0.083,6.521 2.021,6.698 1.938,0.177 10 false *2: for 3ZR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click here

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D or M

·

ON: Shift lever in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 147,125,126,127,128

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport mode select switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
3.INSPECT SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
a.
C245154C39
0.438,1 0.865,1.292 0.427,0.292 2.271,1.646 2.042,1.646 2.042,1.646 1.865,1.302 true 0.313,0.302 0.625,0.5 0.313,0.198 10 false *a 0.542,1.073 1,1.271 0.458,0.198 10 false G36 2.344,1.563 2.656,1.76 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Shift Lever Assembly (Transmission Control Switch))


Disconnect the shift lever assembly (transmission control switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

CHECK POWER SOURCE CIRCUIT (TRANSMISSION CONTROL SWITCH)

4.INSPECT SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C10
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lever Assembly (Transmission Control Switch))


Disconnect the shift lever assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LEVER ASSEMBLY - ECM)

NG

REPLACE SHIFT LEVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LEVER ASSEMBLY - ECM)
a.

Disconnect the G36 shift lever assembly (transmission control switch) connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G36-5 (S) - A62-59 (S) Always Below 1 Ω
G36-5 (S) - Body ground Always 10 kΩ or higher
A62-59 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LEVER ASSEMBLY - ECM)

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the park/neutral position switch assembly connector.


b.
C197711C77
0.292,0.885 0.729,1.146 0.438,0.26 1.667,1.021 2.01,0.427 true 0.385,0.927 0.76,1.156 0.375,0.229 10 false B36 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 2.073,0.344 2.385,0.542 0.313,0.198 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


for 3ZR-FAE:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
B36-1 (RB) - Body ground Ignition switch off Below 1 V



c.
C330140C34
0.438,0.958 0.885,1.24 0.448,0.281 1.625,1 2.021,0.396 true 2.073,0.313 2.385,0.51 0.313,0.198 10 false RB 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.5,1.021 0.969,1.219 0.469,0.198 10 false B101
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


for 3ZR-FE:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B101-1 (RB) - Body ground Ignition switch ON 11 to 14 V
B101-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C298182C03
0.969,1.792 1.344,1.302 true 1.323,1.813 1.469,1.302 true 1.844,1.813 1.708,1.302 true 1.823,0.948 2.292,0.313 true 1.594,0.948 1.771,0.313 true 1.417,0.948 1.229,0.302 true 1.271,0.948 0.854,0.302 true 2.344,0.25 2.656,0.448 0.313,0.198 10 false RB 1.833,0.25 2.146,0.448 0.313,0.198 10 false RL 1.042,0.25 1.354,0.448 0.313,0.198 10 false PL 0.74,0.25 1.052,0.448 0.313,0.198 10 false B 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.865,1.75 1.177,1.948 0.313,0.198 10 false L 1.146,1.75 1.458,1.948 0.313,0.198 10 false NL 1.896,1.75 2.208,1.948 0.313,0.198 10 false DL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D or M Below 1 Ω
Shift lever not in D or M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

for 3ZR-FAE:

Disconnect the B36 park/neutral position switch assembly connector.


b.

for 3ZR-FE:

Disconnect the B101 park/neutral position switch assembly connector.


c.

Disconnect the B93 and A62 ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3ZR-FAE:
Tester Connection Condition Specified Condition
B36-3 (PL) - B93-70 (P) Always Below 1 Ω
B36-2 (RL) - B93-64 (R) Always Below 1 Ω
B36-8 (NL) - B93-69 (N) Always Below 1 Ω
B36-7 (DL) - B93-65 (D) Always Below 1 Ω
B36-4 (B) - A62-23 (NSW) Always Below 1 Ω
B36-3 (PL) or B93-70 (P) - Body ground and other terminals Always 10 kΩ or higher
B36-2 (RL) or B93-64 (R) - Body ground and other terminals Always 10 kΩ or higher
B36-8 (NL) or B93-69 (N) - Body ground and other terminals Always 10 kΩ or higher
B36-7 (DL) or B93-65 (D) - Body ground and other terminals Always 10 kΩ or higher
B36-4 (B) or A62-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher


for 3ZR-FE:
Tester Connection Condition Specified Condition
B101-3 (PL) - B93-70 (P) Always Below 1 Ω
B101-2 (RL) - B93-64 (R) Always Below 1 Ω
B101-8 (NL) - B93-69 (N) Always Below 1 Ω
B101-7 (DL) - B93-65 (D) Always Below 1 Ω
B101-4 (B) - A62-23 (NSW) Always Below 1 Ω
B101-3 (PL) or B93-70 (P) - Body ground and other terminals Always 10 kΩ or higher
B101-2 (RL) or B93-64 (R) - Body ground and other terminals Always 10 kΩ or higher
B101-8 (NL) or B93-69 (N) - Body ground and other terminals Always 10 kΩ or higher
B101-7 (DL) or B93-65 (D) - Body ground and other terminals Always 10 kΩ or higher
B101-4 (B) or A62-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)