Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) › from 2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0221948 CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Either condition is met:
·

"Clearance Warning (Clearance Sonar)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table" are output.

(Click here)


·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly CAN branch wire or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

C306897E17
4.833,4.26 7.094,4.542 2.26,0.281 10 false Clearance Warning ECU Assembly 4.833,4.094 5.292,4.333 0.458,0.24 10 false G166 0.177,1.865 0.625,2.229 0.448,0.365 10 false G174 0.177,2.01 2.271,2.365 2.094,0.354 10 false No. 9 CAN Junction Connector 1.771,2.302 3.26,2.656 1.49,0.354 10 false from IG1 NO.2 Relay 4.073,2.156 5.177,2.458 1.104,0.302 10 false GAUGE 5.656,1.021 6.177,1.177 0.521,0.156 10 false R1 5.656,1.531 6.177,1.688 0.521,0.156 10 false R2 5.656,2.354 6.177,2.51 0.521,0.156 10 false IG 5.656,3.146 6.177,3.302 0.521,0.156 10 false E 5.354,0.896 5.594,1.052 0.24,0.156 10 false 17 5.344,1.427 5.583,1.573 0.24,0.146 10 false 18 5.438,2.208 5.656,2.375 0.219,0.167 10 false 1 5.396,3.021 5.625,3.177 0.229,0.156 10 false 30 1.542,0.875 1.698,1.052 0.156,0.177 10 false 6 1.542,1.406 1.802,1.583 0.26,0.177 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 21 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
a.
C300901C16
1.448,0.406 1.969,0.625 0.521,0.219 0.635,1.031 0.75,1.031 0.75,1.031 0.969,1.188 true 0.75,0.802 0.865,0.802 0.865,0.802 1.031,1.167 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 1.542,0.427 2.094,0.75 0.552,0.323 10 false G166 0.531,0.698 0.844,0.896 0.313,0.198 10 false R1 0.396,0.927 0.708,1.125 0.313,0.198 10 false R2
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G166-17 (R1) - G166-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (R1, R2)

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C300901C17
1.479,0.406 1.99,0.625 0.51,0.219 1.135,1.74 1.26,1.74 1.26,1.74 1.667,1.271 true 2.438,1.188 2.698,0.979 2.698,0.979 2.865,0.979 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 1.552,0.427 2.063,0.719 0.51,0.292 10 false G166 0.99,1.635 1.302,1.833 0.313,0.198 10 false E 2.906,0.865 3.219,1.063 0.313,0.198 10 false IG
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G166-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G166-30 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR